Eurotech Apollo User Manual Download Page 64

Page: 64 / 145

APOLLO user manual

Issue G

Configuring serial ports

To specify serial configuration settings, highlight

Serial Configuration

in the

I/O Device

Configuration

menu and press

Enter

. The following screen is displayed:

The details you are prompted to specify are explained in the following table:

Field

Explanation

Serial Port COM1

Choose how this port is to be configured by selecting one of the
following:

•

Disabled

. The port is not configured at all - it is turned off.

•

Enabled

. You are going to configure the port (by completing

the following fields).

•

Auto

. The port is configured automatically by the BIOS or the

operating system.

OS Controlled

is displayed if configuration of the port is

controlled by the operating system.

Base I/O Address

Specify the I/O address to be used by serial port COM1. This can
be 2E8, 3E8, 2F8 or 3F8.

Interrupt

Specify the interrupt line to be used by serial port COM1. This can
be IRQ3 or IRQ4.

Summary of Contents for Apollo


















































































































































Search results

Summary of Contents for Apollo

Reviews:

Brands by name

Popular brands

Eurotech Apollo, User Manual

Search results

Summary of Contents for Apollo

Reviews:

Brands by name

Popular brands