manualshive.com logo in svg

Eurotech Apollo, User Manual

Share
Download
Eurotech Apollo User Manual Download Page 32

APOLLO user manual 

 

Issue G

 

32 

Connector 

Function 

See … 

J18 

USB ports 3 to 4. 

Page 

45

. 

J19 

IEEE1394 port 1. 

Page 

45

. 

J20 CompactFlash

®

 socket. 

Page 

46

. 

J21 

184-pin DDR SDRAM DIMM Socket. 

N/A 

J22A, J22B  Serial ports 3 to 4. 

Page 

47

. 

J23 Primary 

IDE. 

Page 

48

. 

J24 

Front panel interface. 

Page 

49

. 

J25 RS485/RS422 

port 

Page 

49

. 

J26 IrDA 

connector. 

Page 

50

. 

J27 

Slimline floppy drive interface. 

Page 

50

. 

J1, J2, J3 – Audio connectors 

3.5mm stereo audio jacks are used for audio connection. The audio codec can operate in 
either of the following modes:  

•

 

2.0 mode, which allows for microphone in, line in and line out operation. 

•

 

5.1 mode, which provides six-channel surround sound output. The microphone input 
and line in are not available during six channel mode. 

Selection of 2.0 or 5.1 mode is made using software. 

The audio connectors are illustrated in the following diagram: 

 Ring

 

 

 Sleeve 

Tip 

The pin settings for each connector are described in the following tables: 

Tip 

Ring 

Sleeve 

Summary of Contents for Apollo


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands