LAMPO Multifunction Unit
PICTOGRAMS RELATED TO THE INSTRUCTION MANUAL
HAZARD
HAZARD: this word indicates a hazard with high level of risk that, if not avoided, results in death or serious
injury.
WARNING
WARNING: indicates a hazard with medium level of risk that, if not avoided, could result in death or
serious injury
ATTENTION
ATTENTION: indicates a hazard with low level of risk that, if not avoided, could result in minor or moderate
injury.
IMPORTANT NOTE
General notes useful for the correct consultation of the document
The descriptions preceded by these symbols contain very important information/provisions, in particular with regard to safety. Failure to comply with them
may involve:
•
Hazards for operator safety;
•
Injury even serious to the machine operators (in some cases even death)
•
Loss of contractual warranty;
•
No liability of the Manufacturer.
0.2 PRESERVATION AND VALIDITY OF THE INSTRUCTION MANUAL
The Instruction Manual must be preserved with care and must accompany the machine in all the changes of ownership of its lifecycle.
Preservation must be facilitated by handling it with care, with clean hands and not placing it on dirty surfaces.
No parts can be removed, torn or arbitrarily amended.
The Instruction Manual must be filed in a place protected against moisture and heat and in the vicinity of the machine to which it refers.
The Manufacturer, at the request of the Final User, can provide further copies of the Instruction Manual of the machine.
Validity of the Instruction Manual: the user is reminded that this Instruction Manual reflects the state of technical and technological knowledge used in
the construction of the machine that applies at the moment of its commercialisation, and therefore it cannot be deemed unsuitable and obsolete if it has
subsequently been updated according to new expertise.
0.3 INSTRUCTION MANUAL UPDATE METHOD
The Manufacturer reserves the right to amend the project and improve the machine without communication to the Final Users and without updating the
Instruction Manual already delivered to the Final User.
However, in case of amendments to the machine installed at the Final User premises, agreed with the Manufacturer and involving the amendment of one
or more chapters of the Instruction Manual, the Manufacturer will send the addressees of the Instruction Manual involved the chapters involved in the
amendment, with the new global revision model of it.
It is the responsibility of the Final User, following the instructions available together with the updated documentation, replace in all copies owned the old
chapters with the new ones, the initial page and the index with those with the new revision level.
The Manufacturer is responsible for the descriptions given in Italian; any translations cannot be checked in full, so if an inconsistency is detected, it is
necessary to refer to the Italian version and, if necessary, contact the Manufacturer's technical office, which will make the amendment deemed appropriate.
Should the Instruction Manual become illegible or in any case difficult to consult, the Final User is obliged to request a new copy to the Manufacturer
before performing any operation on the machine
It is strictly forbidden to remove or rewrite any part of the Instruction Manual
Instructions, drawings and documents contained in this Instruction Manual are of a confidential nature, strictly owned by the Manufacturer and
cannot be reproduced in any manner, either in whole or in part, without the prior authorisation of the manufacturer.
The Final User is required to comply with the instructions contained in this Instruction Manual and in the technical documentation referred to in
the contract.
The Manufacturer is not responsible for any inconvenience that may arise as a result of the incorrect use of these recommendations.
0.4 ADDRESSEES OF THE INSTRUCTION MANUAL
This Instruction Manual is intended only for the subjects indicated in Par. 0-6.
Other figures are also mentioned in the various chapters, always referable to the Qualification of the interested subjects of Par. 0.6, such as:
Exposed person - Personnel not in charge
This means any person fully or partly inside an hazardous area.
Operator - Personnel in charge
This means the person(s) in charge of installing, operating, adjusting, cleaning, repairing and moving a machine and carrying out its maintenance.
Qualified personnel or qualified operator
This means the persons who have attended specialisation courses for special tasks (e.g.: electricians) and have experience in relation to the installation,
commissioning and maintenance, repair and transport of the machine.
Intended Use of the Machine
The machine is intended for an industrial use, and therefore professional and not generalised, for which its use must be entrusted to qualified personnel, in
particular that:
•
Have reached the age of majority;
•
Are physically and psychically fit to perform work of particular technical difficulty;
•
Have been suitably trained to the use and maintenance of the machine;
5
Summary of Contents for LAMPO GREEN
Page 2: ......
