background image

 

Euphonix TT007 Operation Manual

Appendix

30

 Why won’t my Lynx modules lock?

Be sure each module has a unique address number.

Be sure LTC from the Master is being sent to the TcR port and that the port is 
selected as 

From Master

 if no video sync is present.

Be sure that the Lynx modules are running current software versions. Euphonix 
has tested the TT007 using the following software versions:

Lynx I: v500_26L

Lynx II: v700_11

Why does the video sync LED light even when video is not con-

nected?

This is caused by a sensing bug in the video reader chip that, in some cases, confuses 
open air RF as a video signal. Cycling the TT007’s power on/off usually clears the 
erroneous indication.

Why am I having problems making my MicroLynx / Audio Kinetics 

synchronizer work with the TT007?

These synchronizers are not yet supported.

How can I adjust the LCD viewing angle contrast on my display?

There is no software-based control for this feature. There is an adjustment potentiometer 
inside the TT007 on the main circuit board next to the front panel connectors. 

Why does my video deck not unthread the tape and high-speed 

wind when I select Rew/FF?

The Windspeed option is selected in the TT007 Utility Menu. With this option set, the 
first press of Rew/FF will result in a threaded Scan and the second press will unthread 
the tape and initiate a high-speed wind.

A.2

Explanation of Controllers

The RS-422 ports on the TT007 are wired (normalled) to send (Tx) and receive (Rx) 
data to and from tape-based machines. To connect any device to the TT007, use a 
standard, straight-thru, pin-to-pin cable. The TT007 may also emulate a device simply 
by swapping the Tx and Rx lines of the RS-422 cable. In this configuration, the TT007 
may be considered a 

virtual machine

.

Summary of Contents for TT007











































Reviews: