EUCHNER MGB2-L1 Operating Instructions Manual Download Page 5

Page: 5 / 60

2500233-04-10/21 (translation of the original operating instructions)

Operating Instructions Safety Systems

MGB2-L1…-BR.-… / MGB2-L2…-BR.-… and MGB2-L1…-BP.-… / MGB2-L2…-BP.-…

1. About this document

1.1. Scope

These operating instructions are valid for all MGB2-L1…-BR.-… / MGB2-L2…-BR.-… and MGB2-L1…-BP.-… / MGB2-L2…-BP.-…

These operating instructions, the document

Safety information

and any enclosed data sheet form the complete user infor-

mation for your device.

Series

Guard locking types

System families

Product versions

MGB2

L1 (guard locking by spring force)

…-BP…

From V1.0.0

…-BR…

L2 (guard locking by solenoid force)

…-BP…
…-BR…

1.1.1. Notes on older product versions

Products with lower product versions or without a version number are not described by these operating instructions. Please

contact our support team in this case.

1.2. Target group

Design engineers and installation planners for safety systems on machines, as well as setup and servicing staff possessing

special expertise in handling safety components as well as expertise in the installation, setup, programming and diagnostics

of programmable logic controllers (PLCs).

1.3. Key to symbols

Symbol/depiction

Meaning

This section applies to operation as MGB2-BP

This section applies to operation as MGB2-BR

DIP

OFF

In this section, attention must be paid to the DIP switch settings

Printed document

Internet

www

Document is available for download at www.euchner.com

DANGER

WARNING

CAUTION

Safety precautions

Danger

of death or severe injuries

Warning

about possible injuries

Caution

Slight injuries possible

NOTICE

Important!

Notice

about possible device damage

Important

information

Tip

Useful information

Summary of Contents for MGB2-L1





























































Search results

Summary of Contents for MGB2-L1

Reviews:

EUCHNER MGB2-L1, Operating Instructions Manual, Page: 5 / 60

Search results

Summary of Contents for MGB2-L1

Reviews: