manualshive.com logo in svg

EUCHNER MGB2-L1, Operating Instructions Manual, Page: 35 / 60

Share
Download
EUCHNER MGB2-L1 Operating Instructions Manual Download Page 35

35

2500233-04-10/21 (translation of the original operating instructions)

Operating Instructions Safety Systems

MGB2-L1…-BR.-… / MGB2-L2…-BR.-… and MGB2-L1…-BP.-… / MGB2-L2…-BP.-…

EN

13.7.2. Deactivating guard lock monitoring

WARNING

Risk of injury due to inactive guard lock monitoring.

 

Ì

With inactive guard lock monitoring, the guard locking position does not influence the safety out-

puts. The guard can be opened immediately. This setting is not allowed to be used in applications 

in which, e.g., there is a hazard due to overrunning machinery movement. With inactive guard lock 

monitoring, guard locking must be used only for process protection.

1.  Switch off power supply.
2.  Set DIP switches 2, 5 and 8 as shown.

Deactivating guard lock monitoring

Activating guard lock monitoring

ON

3 4

6 7

8

5

2

1

ON

3 4

6 7

8

5

2

1

3.  Switch on power supply for 5 s. 

 

¨

The change is confirmed by positive acknowledgment.

4.  Switch off power supply and set DIP switch 8 to OFF.

 

¨

The next time the device is started, it operates in the operating mode set.

13.7.3. Activating release monitoring

NOTICE

When release monitoring is active, the system enters into a latching fault when the escape release or 

auxiliary release is actuated.
See 

System status table

, 

signal sequence incorrect

 status (DIA red, Lock flashes 1 time).

1.  Switch off power supply.
2.  Set DIP switches 3 and 8 as shown.

Deactivating release monitoring

Activating release monitoring

ON

2

4

6 7

8

5

3

1

ON

2

4

6 7

8

5

3

1

3.  Switch on power supply for 5 s. 

 

¨

The change is confirmed by positive acknowledgment.

4.  Switch off power supply and set DIP switch 8 to OFF.

 

¨

The next time the device is started, it operates in the operating mode set.

Summary of Contents for MGB2-L1





























































Reviews:

No comments