manualshive.com logo in svg

EUCHNER CES-AZ-ALS Series, Operating Instructions Manual, Page: 6 / 52

Share
Download
EUCHNER CES-AZ-ALS Series Operating Instructions Manual Download Page 6

Operating instructions
Non-Contact Safety System CES-AZ-UES-…

6

(Translation of the original operating instructions) 2105274-12-08/20

Important!

 

Ì

The user is responsible for the proper integration of the device into a safe overall system. For this 

purpose, the overall system must be validated, e.g. in accordance with EN ISO 13849-2.

 

Ì

Correct use requires observing the permissible operating parameters (see technical data).

 

Ì

If a data sheet is included with the product, the information on the data sheet applies.

 

Ì

It is only allowed to use components that are permissible in accordance with the table below.

Table 1:  Possible combinations for CES components

Evaluation unit

Read head

Actuator

CES

-A-BSP-104970

104970

CES

-A-BBN-106600

106600

CES

-A-BDN-06-104730

104730

CES

-A-BBA

071840

CES

-A-BCA

088786

CES

-A-BQA

098108

CES

-A-BDA-20

084720

CES

-A-BDA-18

156935

CES

-A-BMB

077791

CEM-A-BE05

094805

 

CEM-A-BH10

095175

CET

-A-BWK-50X

096327

CKS-A-BK1…

CKS key

CES-AZ-UES-01B

105139

CES-AZ-UES-02B

105140

CES-AZ-UES-04B

105141

CES-A-LSP-…

All items

20

CES-A-LNN-…

All items

15

19

CES-A-LCA-…

All items

15

15

16

16

CES-A-LNA-…

All items

15

15

16

16

CES-A-LQA-SC

095650

15

15

23

CES-A-LMN-SC

077790

8

8

9

9

5

CEM-A-LE05K-S2

094800

CEM-A-LE05R-S2

095792

CEM-A-LH10K-S3

095170

CEM-A-LH10R-S3

095793

CET1-AX-LRA-…

095735

CET1-AX-LDA-…

100399

CKS-A-L1B-…

113130

l

Key to symbols

l

Combination possible

15

Combination possible, typ. switch-on distance 15 mm

Combination possible, guard locking for process protection

Combination possible, guard locking for personnel protection

Combination not permissible

Summary of Contents for CES-AZ-ALS Series





















































Reviews:

No comments