manualshive.com logo in svg

EUCHNER 156233, Operating Instructions Manual, Page: 24 / 40

Share
Download
EUCHNER 156233 Operating Instructions Manual Download Page 24

Operating Instructions

Non-Contact Safety Switch CES-I-BR-.-C07-…

24

(translation of the original operating instructions) 2510145-05-08/21

14.  Status and error messages

14.1.  LED indicator

LED

Color

STATE

green

DIA

red

Important!

If you do not find the displayed device status in the following tables, this indicates an internal device 

fault. Contact the manufacturer.

Key to symbols

LED not illuminated

LED illuminated

1 x 

inverse

LED illuminated, briefly goes off 1 x

 

quickly

LED flashes quickly (5 Hz)

 

slowly

LED flashes slowly (1 Hz)

 

3 x

LED repeatedly flashes three times

 

¨

 

LEDs flash alternately

14.2.  Status messages

Operating 

mode

LED indicator

Safety 

outputs 

FO1A / 

FO1B

Door 

position 

signal 

OD

Status

STATE

green

DIA

red

Self-test

 

5 Hz (5 s)

off

off

Self-test after operating voltage is switched on.

 

quickly

 

1 x

No communication with the BR/IO-Link Gateway.

Normal operation

on

on

Door is closed. The safety outputs of the preceding device in a series connec-

tion are switched on.

 

1 x inverse

off

on

Door is closed. The safety outputs of the preceding device in a series connec-

tion are switched off.

 

1 x

off

off

Door is open.

 

6 x inverse

on

on

Door is closed. The actuator is in the limit range. Door must be readjusted. 

Teach-in operation

 

3 x

off

off

Device is in teach-in standby (see chapter 

12.1. Teach-in function for actuator 

(only for unicode evaluation) on page 22).

 

slowly

off

teach-in operation. Door is closed

.

  

¨

  

off

Positive acknowledgment after successful teach-in operation.

Err

or

  or

 

 1x inverse

off

depending 

on the 

error

Error message, see chapter 

14.3. Error messages on page 25.

LEDs

Summary of Contents for 156233









































Reviews:

No comments