manualshive.com logo in svg

EUCHNER 156233, Operating Instructions Manual, Page: 23 / 40

Share
Download
EUCHNER 156233 Operating Instructions Manual Download Page 23

23

2510145-05-08/21 (translation of the original operating instructions)

Operating Instructions

Non-Contact Safety Switch CES-I-BR-.-C07-…

EN

12.2.  Electrical function test

WARNING

Danger of fatal injury as a result of faults in installation and functional check.

 

Ì

Before carrying out the functional check, make sure that there are no persons in the danger zone.

 

Ì

Observe the valid accident prevention regulations.

After installation and any fault, the safety function must be fully checked. Proceed as follows:
1.  Switch on operating voltage.

 

¨

The machine must not start automatically.

 

¨

The safety switch carries out a self-test. The green STATE LED flashes for 5 s at 5 Hz. The green STATE LED then flashes 

at regular intervals.

2.  Close all guards.

 

¨

The machine must not start automatically. 

 

¨

The green STATE LED illuminates continuously.

3.  Enable operation in the control system.
4.  Open the guard.

 

Ì

The machine must switch off and it must not be possible to start it as long as the guard is open.

 

Ì

The green STATE LED flashes at regular intervals.

Repeat steps 2 - 4 for each guard.

13.  Factory reset

A factory reset deletes the parametrization and restores the device’s factory settings.
To perform a factory reset, connect the two outputs FO1A and FO1B to 0 V when switching on or send the command Ox1E 

via IO-Link communication (see chapter 

11.3.2. Acyclical data (device data and events) on page 21)

.

Summary of Contents for 156233









































Reviews:

No comments