IMPORTANT: SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING
PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION.
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts,
cuts/ abrasions, and other hazards please read all warnings and instructions included with and on the
fixture box and all fixture labels.
• This installation should only be performed by a qualified electrician in accordance with the
National Electrical Code and all relevant local codes.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction
and operation and any hazards involved. Regular fixture maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will
depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens
should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed
with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens
and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should
have been damaged during transit. Thoroughly inspect the fixture for any freight damage; freight
damage should be reported to the delivery carrier.
• WARNING: RISK OF ELECTRIC SHOCK. Make sure power supply is OFF before installing or maintaining
fixture. No user serviceable parts inside.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• The fixtures must be wired in accordance with the National Electrical Code and all applicable local
codes. Proper grounding is required for safety.
• All wiring connections should be capped with UL approved recognized wire connectors.
• CAUTION: RISK OF INJURY. Never perform maintenance or cleaning while fixture is energized.
Disconnect power and allow fixture to cool before maintaining.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer’s warnings, recommendations and restrictions for: driver type, burning position,
mounting locations/methods, replacement and recycling.
INSTALLATION FOR LED WALL PACK WP42M SERIES
Head Offi ce -
1850 Wilson Ave. · Toronto, ON · M9M 1A1 ·
Tel:
416.741.7336 ·
Fax:
416.741.9104
Toll Free:
in Canada. 1.800.661.9610 · in USA. 1.888.762.5384 (SOCKETS4U)
www.etlin-daniels.com · For sales/service questions - [email protected]
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or
performing maintenance.
• CAUTION: RISK OF FIRE. Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.
• CAUTION: RISK OF PRODUCT DAMAGE. Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
• Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the
luminaire must be checked for compatibility with the luminaire prior to installation. Never connect an
LED product directly to a dimmer pack that has not been pre-approved. LED fixtures must be powered
directly off a switched circuit.
• Unless individual product specifications deem otherwise: do not restrict fixture ventilation. Allow for
some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other
material that will prevent convection or conduction cooling.
• Unless individual product specifications deem otherwise: do not exceed fixture maximum ambient temperature.
• Only use fixture in its intended location.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be
worn during all installation or servicing of the unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
• Some components inside the fixture may not be serviceable. In the unlikely event your unit may require
service, stop using the unit immediately and contact your sales representative for assistance.
• User should prepare necessary accessories and spare parts (not provided) including junction box, cross
bar, junction box gasket, surface plate and screws.
• Always read the fixtures complete installation instructions prior to installation for any additional fixture
specific warnings.
Wiring
Wire input end of the LED driver to supply wires using appropriate wire nut according to
wiring section. Wire connections must be insulated and waterproof.
1. Connect the Black / Brown lead to LINE(+) supply lead.
2. Connect the WHITE / BLUE lead to NEUTRAL / COMMON (-) supply lead.
3. Connect the GREEN leads of front housing and back housing to GROUND supply lead.
4. For 0-10V dimming, use purple (+) and grey (-) wires.
BLACK / BROWN = HOT / LINE
WHITE / BLUE = NEUTRAL / COMMON
GREEN / YELLOW = GROUND
Purple (+) // Grey (-)
ELECTRICAL
SYSTEM
0-10V DIMMING
SYSTEM (IF ANY)
CAUTION: INTENDED APPLICATION
Input Voltage: 120-277V / 347V. 50/60Hz
CHECK PRODUCT LABEL RATINGS BEFORE ATTEMPTING INSTALLATION.
MIN. 90°C supply connectors
Operating temperature: -30°C to +40°C
Suitable for wet location
Mounting height: above 4’ (1.2 m)
