ETIC 1220 User Manual Download Page 62

Page: 62 / 64

APPENDIX 2
HTML server

Page 62

User’s guide ref 9014709-02

XSLAN SHDSL switch

Alarms

To set the alarms

SNMP

To define traps and SNMP server

To defines the conditions the output will open

To enter the alarm email parameters

IP to RS gateway

(XSLAN-1220, 1230, 2220 & 2230)

Modbus

To configure the modbus gateway.

Transparent

To configure the raw, multicast & telnet gateway

Unitelway

To configure the unitelway gateway

Diagnostics

Logs

To display logs

Network status

To display all the parameters of the connection in use
MAC & IP @,
SHDSL connection : data rate, error rate, statistics

Gateway status

To display the status of the gateway

Microswitch

To display the micro switches current position

Ping

To ping a machine

Table of routes

To display the table of routes

Ping

To ping a machine

IO control

To display the IOs status

About

To display the firmware and hardware identification

Summary of Contents for 1220

































































Search results

Summary of Contents for 1220

Reviews:

ETIC 1220, User Manual, Page: 62 / 64

Search results

Summary of Contents for 1220

Reviews: