ETIC 1220 User Manual Download Page 46 | Manualshive

Page: 46 / 64

ETIC 1220 User Manual Download Page 46

HTML SET UP & DIAGNOSTIC

To configure the Modbus server gateway

,

•

select the modbus menu and then modbus server,

•

enable the modbus server gateway and set the parameters as follows:

“Modbus protocol” parameter :

Select the RTU or ASCII option

“Activate Proxi cache” parameter :

Enable the proxi option if you wish to avoid to frequent requests on the
serial interface.

“Cache refreshment period” parameter :

the same request is received twice or more inside that delay, it will be
sent only once to the slave on the serial interface.

“Timeout waiting for the answer” parameter :

Set up the timeout the gateway has to wait for the answer of the modbus
slave.

“Local retry” parameter :

Set up the number of times the gateway will repeat a request to one of the
modbus slaves on the serial interface before declaring a failure.

“Inter-character gap” parameter :

Set up the maximum delay the gateway will have to wait between a

Page 46

User’s guide ref 9014709-02

XSLAN SHDSL switch

«
...
44
45
46
47
48
...
»

Summary of Contents for 1220

































































Reviews:

No comments