manualshive.com logo in svg

Etic Telecom XLAN+ Series, Setup Manual

Share
Download
Etic Telecom XLAN+ Series Setup Manual Download Page 40

SETUP 

Page 40

 

DOC_DEV_XS_Setup guide_C

 

 

10

 

IGMP snooping  

10.1

 

Overview 

By  default,  a  switch  floods  all  multicast  frames  to  all  is  ports.  In  heavy  traffic  scenarios,  this  can  cause 
saturation of the links, especially on slower SHDSL connections. To avoid this and take informed bridging 
decisions, a switch can inspect the IGMP traffic that peers doing multicast exchange. 
 
In a typical multicast enabled network, there is a multicast router. This device queries periodically using IGMP 
the other hosts to know which peers want to receive what multicast traffic.  
The switch, when forwarding the frames, will check whether or not it should forward or block a given traffic on 

a given port.  
 
When there is no multicast router to query the network, one of the IGMP snooping enabled switch can do the 
queries. The device with the lowest IP address is elected as the querier for the network.  
 

10.2

 

Setting up the IGMP snooping function 

•

 

In the menu, choose 

Setup > Ethernet and switching > IGMP snooping

. 

•

 

Tick the 

Enable IGMP snooping

 checkbox. 

 

 

 

Enable IGMP snooping 

Enable the filtering/forwarding of IP multicast packets based on IGMP traffic. 
 

Enable IGMP snooping querier mode 

Enable the XS to be elected querier if there is no router on the network. 

 

Router mode for LAN1 
Router mode for LAN2 
Router mode for SH1 
Router mode for SH2 
Router mode for SH3 
Router mode for SH4 

Accept all multicast traffic from this port. 

 

Summary of Contents for XLAN+ Series





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands