Etic Telecom XLAN+ Series Setup Manual Download

Page: 18 / 84

SETUP

Page 18

DOC_DEV_XS_Setup guide_C

3.3

Step 2 : SHDSL test and set up adjustment

•

Connect the XS to the twisted pairs. The wires of the same twisted pair can be reversed.

•

Power on the XS.

•

The connection takes about 45 s to establish with the « standard » profile and may takes a longer time with
other profiles.

•

The SHDSLx LEDs attached to each port displays the state of the connection as described in the table
below.

State of the connection

SHDSL LED

The other XSLAN was not detected
(for example when the line is not connected)

Blinking 0,1 s ON / 2 s OFF

Data rate negotiation

Blinking 0,3 s ON / 0,3 s OFF

Connected

Steady on

Traffic on the link

Flashing

•

Once connected, choose

Diagnostics > Network status > Interfaces

in the menu to check the SHDSL link

quality.

Summary of Contents for XLAN+ Series





















































































Search results

Summary of Contents for XLAN+ Series

Reviews:

Related manuals for XLAN+ Series

Brands by name

Popular brands

Etic Telecom XLAN+ Series, Setup Manual

Search results

Summary of Contents for XLAN+ Series

Reviews:

Related manuals for XLAN+ Series

Brands by name

Popular brands