manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 49

 

1.  Click in the Ingress or Egress Text Box for the appropriate port. 

2.  Type in the ingress/egress rate for the port according to the values listed above. 

.  Click on the 

Update Setting

 button. 

 

3

 

Figure 19: Rate Control 

 

page: 

f packets that a particular 

RMON Statistics 

To navigate to the 

RMON Statistics

1.  Click on the 

+

 next to 

Port

. 

2. Click on 

RMON Statistics

. 

RMON Statistics gives a detailed listing of the types and quantity o
port has seen since the last reboot of the switch (see 

Figure 20

). 

To view the RMON statistics for a particular port on the EX24000 Switch: 

1.  Click on the link to the port at the top of the RMON Statistics page. 

To clear the RMON statistics for a particular port on the EX24000 Switch: 

1.  Click on the link to the port at the top of the RMON Statistics page. 

3.  The statistics for the port will update every ten seconds. 

2.  Click on the 

Clear

 button at the bottom of the page. 

49 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands