manualshive.com logo in svg

EtherWAN EX24000, User Manual

The EtherWAN EX24000 is a cutting-edge networking device designed for seamless data transmission. To harness its full potential, make sure to refer to our comprehensive User Manual. Easily accessible for download from our website, our manual grants you free access to all the crucial information you need to optimize your network experience.

Share
Download
background image

 

 

Figure 97: GVRP Configuration Access Switch 

Enabling the GVRP Protocol at the Port Level 

To navigate to the 

Other Protocols / GVRP 

page (see 

Figure 95

): 

1.  Click on the 

+

 next to 

Other Protocols

. 

2. Click on 

GVRP

. 

To enable the GVRP protocol locally at the port level, for both the Access switch and the 

Distribution switch, apply the following procedures to all the Trunk Ports of the switch: 

1.  For all the Trunk Ports under the 

Per Port Setting (include LAG)

 section, choose 

the 

Enable

 option from the drop-down list under the 

GVRP

 column. 

2.  For all the Trunk Ports under the 

Per Port Setting (include LAG)

 section, choose 

the 

Active

 or 

Normal 

option from the drop-down list under the 

GVRP Applicant

 

column. 

o

 

Active

 - Use this option if you want to run the GVRP protocol on that Trunk 

Port even if it is blocked by the STP protocol.  

o

 

Normal 

– Use this option if you do not wish to run the GVRP protocol on a 

Trunk Port when it is being blocked by the STP protocol. 

3.  For all the Trunk Ports under the 

Per Port Setting (include LAG)

 section, choose 

the 

Enable

 option from the drop-down list under the 

GVRP Registration

 column. 

4.  Click on the 

Update Setting

 button. 

5.  Save the configuration (see the 

Save Configuration Page

) 

 

197 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Related manuals for EX24000

D-Link D DGS-3048 DGS-3048 Datasheet preview
D DGS-3048 DGS-3048
Brand: D-Link Pages: 3
X10 WM100 Product Manual preview
WM100
Brand: X10 Pages: 20
Pakedge SX-8P Quick Start Manual preview
SX-8P
Brand: Pakedge Pages: 24
Gefen EXT-DVI-441DL User Manual preview
EXT-DVI-441DL
Brand: Gefen Pages: 31
ORiNG IGS-1082GP Quick Installation Manual preview
IGS-1082GP
Brand: ORiNG Pages: 2
Theben TIMEGUARD WF10COM Installation & Operating Instructions Manual preview
TIMEGUARD WF10COM
Brand: Theben Pages: 35
VADA FLOW BOSS VFB-DSU Installation Manual preview
FLOW BOSS VFB-DSU
Brand: VADA Pages: 17
REV Ritter RF102R Assembly And Operating Instructions Manual preview
RF102R
Brand: REV Ritter Pages: 15
LEGRAND Raritan Dominion LX II Quick Setup Manual preview
Raritan Dominion LX II
Brand: LEGRAND Pages: 7
Magnum M9-EKCS Quick Start Manual preview
M9-EKCS
Brand: Magnum Pages: 3
Cabletron Systems Cyber SWITCH 1000 User Manual preview
Cyber SWITCH 1000
Brand: Cabletron Systems Pages: 106
H3C S5130S-EI series Hardware Information preview
S5130S-EI series
Brand: H3C Pages: 67
cable matters 202046 Quick Start Manual preview
202046
Brand: cable matters Pages: 8
Accton Technology EtherHub-24s Quick Installation Manual preview
EtherHub-24s
Brand: Accton Technology Pages: 7
H3C S9820-64H Manual preview
S9820-64H
Brand: H3C Pages: 39
InHand InSwitch ISM-P Series Web Config Manual preview
InSwitch ISM-P Series
Brand: InHand Pages: 81
SOMFY COMMANDE MURALE RTS Manual preview
COMMANDE MURALE RTS
Brand: SOMFY Pages: 2
LEGRAND Wattstopper EOSW Series Manual preview
Wattstopper EOSW Series
Brand: LEGRAND Pages: 12

Brands by name

Popular brands

Load more brands