EtherWAN EX24000 User Manual Download Page 122

Page: 122 / 239

Usage Example:

switch_a>

enable

switch_a#

configure terminal

switch_a(config)#

interface fe1

switch_a(config-if)#

bridge-group 1 path-cost 200000

switch_a(config-if)#

bridge-group 1 priority 128

switch_a(config-if)#

switch_a(config)#

switch_a#

To modify the MSTI Port Priority and MSTI Port Path Cost for an Instance on a switch,
please use the below CLI commands:

CLI Command Mode:

Interface Configuration Mode

CLI Command Syntax:

bridge-group 1 instance

<1-15>

path-cost

<1-200000000>

bridge-group 1 instance

<1-15>

priority

<0-240>

Usage Example:

switch_a>

enable

switch_a#

configure terminal

switch_a(config)#

interface fe1

switch_a(config-if)#

bridge-group 1 instance 1 path-cost 20000

switch_a(config-if)#

bridge-group 1 instance 1 priority 128

switch_a(config-if)#

switch_a(config)#

switch_a#

Adding a Port to an MSTI Instance

To add a port to a MSTI instance (this port must be a member port of the VLAN that is
mapped to the MSTI instance), please use the below CLI commands:

CLI Command Mode:

Interface Configuration Mode

122

EX24000 Switch Users Guide

Summary of Contents for EX24000
















































































































































































































































Search results

Summary of Contents for EX24000

Reviews:

Related manuals for EX24000

Brands by name

Popular brands

EtherWAN EX24000, User Manual

Search results

Summary of Contents for EX24000

Reviews:

Related manuals for EX24000

Brands by name

Popular brands