manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 101

 

 

Point to Point Link 

By default, RSTP will assume any full-duplex link as a 

Point to Point Link

, but if the 

switch detects that the neighbor switch is not running the RSTP protocol, it will assume 
the port to be a 

Shared Port

. You can force a port to be a 

Shared Port

, if you know in 

advance that there will be more than one switch connecting to this link (through an 
unmanaged switch, for example), or if you know in advance that the other switch on this 
link will be running the older STP protocol. 

 

To manually force a port to be a 

Shared Port 

or a 

Point to Point Link: 

 

1.  Choose the correct port from the drop down list under 

Port

, and choose 

Enable

 

or 

Disable

 under 

Point to Point Link

 (see 

Figure 45

).  

2.  Click on the 

Update Setting

 button. 

3.  Save the configuration (see the 

Save Configuration Page

) 

Edge Port 

By enabling the 

Edge Port

 feature on a port, the switch will stop reacting to any linkup 

event on this port, and will not send out any Topology Change notification to the 
neighbor bridges. 

1.  Choose the correct port from the drop down list under 

Port

, and choose 

Enable

 

or 

Disable

 under 

Edge Port

 (see 

Figure 45

).  

2.  Click on the 

Update Setting

 button. 

3.  Save the configuration (see the 

Save Configuration Page

) 

 

101 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands