
pull gently on the incoming cable to remove excess
cable from inside the fitting and draw the box back
to the bottom of the fitting.
7. Replace the brass nut and tighten securely.
8. Fit the lamp.
9. If required, drop a coloured filter into the fitting
and allow to rest on the lamp.
10. Replace the glass cover and stainless steel ring.
When refitting the cover, ensure that the gasket
and glass are located accurately to maintain the
protection against ingress of moisture.
11.
IMPORTANT:
Tighten each of the screws a little at
a time, each in turn so that all screws are tightened
evenly.
12. Press the fitting into the hole ensuring the spring
clips hold it securely.
13. Restore the power supply and switch on.
Energy Efficiency
The following suggestions will help you protect the
environment and save money on your electricity bills:
• Always switch lights off when not in use.
• You can often use a lower Wattage bulb than the
maximum stated, e.g. if the maximum stated is 50W,
try using a 35W.
• This product is suitable for use with Low Energy
bulbs. Please use a Low Energy equivalent wherever
possible.
Safety Markings
Cleaning
Clean this light fitting with a soft dry cloth.
Disconnect the power and clean the exterior only
of this fitting with a moist (not wet) cloth.
The glass lens may be removed and washed in a mild
detergent solution. Make sure it is completely dry
before putting back on your light fitting.
Do not use any chemical or abrasive cleaners.
If installed in a driveway, take care when using
mechanical cleaning machinery.
Lamp Replacement
1. Switch off the electricity at the mains.
2. Remove the diffuser by undoing the three hex drive
screws and lifting off.
3. Remove and replace lamp
4. Replace the glass cover and stainless steel ring
When refitting the cover, ensure that the gasket
and glass are located accurately to maintain the
protection against ingress of moisture.
5.
IMPORTANT:
Tighten each of the screws a little at
a time, each in turn so that all screws are tightened
evenly.
6. Restore the power supply and switch on.
Replacement Lamp Type
Wattage Size/Type
Location
GDL50SS
1W/3W
GU10 LED
1
9W
GU10 CFL
2
50W
GU10 halogen 3
GDL53
7W/9W
GX53 CFL
2
Locations
1 - Suitable for use in any location
2 - Suitable for use in most locations
3 - Suitable for use in locations out of normal reach
If you experience problems...
If your light is defective or develops a fault, please
return it to the place where you bought it. You can call
our Helpline for advice. The Helpline will gladly give
advice on any aspect of any Eterna Lighting product
but may not be able to give specific instructions
regarding individual installations.
If in doubt, consult a qualified electrician.
Help Line
Tel:
01933 673 144
Fax:
01933 678 083
Email: [email protected]
For all other information visit our website
www.eterna-lighting.co.uk
SAFETY AND INSTALLATION
INSTRUCTIONS
Models:
GDL50SS, GDL53
Stainless Steel Ground/Deck Light
IMPORTANT!
Please read these instructions before installing your new fitting.
Please retain for future reference.
Eventually, you may want to replace this light fitting
When your CFL or LED lamp comes to the end of its life or you choose to update or upgrade it by replacing it, please do not dispose
of it with your normal household waste, please recycle where facilities exist. When you need to dispose of the lamp, check with your
retailer or local authority for suitable options. New regulations require the recycling of Waste from Electrical and Electronic Equipment
(European “WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd January 2007). Environment Agency Registered
Producer: WEE/GA0248QZ
Pack Contents
Ground light fitting x 1
Hexagonal drive key x 1
IP44 connection box (GDL50SS only) x 1
9W CFL (compact fluorescent lamp) (GDL53 only) x 1
Colour filters (GDL53 only) x 3
Installation Instructions and Care
08
11
28P
A
IP68