Etec EXTA7032 Installation Manual Download

Page: 1 / 12

Swiveling, Tilting, Rotating

Flat Panel Wall Mount

Installation Guide

Model: EXTA7032

This product Wall Mount frame is intended for use only with an apparatus which has a maximum weight of 77 lbs. See apparatus

instructions. Using with an apparatus heavier than the maximum weight indicated may result in instability and cause possible

injury.

READ THIS FIRST Read this entire manual! Do not attempt to install this product if you do not understand the instructions.

Contact a qualified mount installer if you have any doubts about a safe and secure mount installation, or if you are not sure what

specific wall materials you are attaching this mount to. Check all the parts carefully to make sure there are no missing or

damaged parts. Improper installation may result in damage to your TV, property, and personal injury.

• Supports most 32” - 70” Televisions

• Maximum weight capacity: 77 lbs.

• Supports VESA Sizes up to 600x400

• Easy installation

• Tilt range: +5 to -15 degrees

• Swivel range: 180 degrees

• Extension range: 3.1” to 15.8”

• Rotation range: +5 to -5 degrees

For technical assistance or troubleshooting please call

1-855-994-3832 or visit www.sibrandssupport.com

Summary of Contents for EXTA7032








