ETC Net3 Four Port Gateway Setup Manual Download Page 5

2

Please email comments about this manual to: 

[email protected]

Help from ETC Technical Services

If you are having difficulties, your most convenient resources are provided in this user 

manual. To search more widely, try the ETC website at 

www.etcconnect.com

. If none of 

these resources is sufficient, contact ETC Technical Services directly at one of the offices 

identified below.

C A U T I O N :

Caution statement indicates situations where there may be undefined or 
unwanted consequences of an action, potential for data loss or an equipment 
problem.

C A U T I O N :

Caution statement indicates situations where ESD (Electro-Static Discharge) may 
damage equipment. Special precautions should be taken to keep your self 
grounded to avoid damaging the equipment.

W A R N I N G :

A Warning statement indicates situations where damage may occur, people 
may be harmed, or there are serious or dangerous consequences of an 
action.

W A R N I N G :

RISK OF ELECTRIC SHOCK! This warning statement indicates situations 
where there is a risk of electric shock.

Americas

United Kingdom

Electronic Theatre Controls Inc.

Electronic Theatre Controls Ltd.

Technical Services Department

Technical Services Department

3031 Pleasant View Road

26-28 Victoria Industrial Estate

Middleton, WI 53562

Victoria Road, 

800-775-4382 (USA, toll-free)

London W3 6UU England

+1-608 831-4116

+44 (0)20 8896 1000

[email protected]

[email protected]

Asia

Germany

Electronic Theatre Controls Asia, Ltd.

Electronic Theatre Controls GmbH

Technical Services Department

Technical Services Department

Room 1801, 18/F

Ohmstrasse 3

Tower 1, Phase 1, Enterprise Square

83607 Holzkirchen, Germany

9 Sheung Yuet Road

+49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong

techserv-hoki@etcconnect.com

+852 2799 1220

[email protected]

Summary of Contents for Net3 Four Port Gateway





















Reviews: