www.estesrockets.com
Estes® Industries
1295 H Street
Penrose, CO 81240
PRINTED IN CHINA
FLYING MODEL ROCKET
KIT INSTRUCTIONS
PARTS
ASSEMBLY TIP
Read all instructions before
beginning work on your model.
Make sure you have all parts
and supplies.
TEST FIT ALL PARTS TOGETHER
BEFORE APPLYING ANY GLUE!
If any parts don't fit properly, sand as
required for precision assembly.
SCISSORS
PENCIL
RULER
FINE SAND
PAPER
(#400-600 GRIT)
MASKING
TAPE
PLASTIC
CEMENT
MODELING
KNIFE
SPRAY
PRIMER
(WHITE)
SPRAY PAINT:
(OLIVE DRAB,
LIGHT GRAY)
SPRAY DULL
COAT
(OPTIONAL)
PAINT PEN
(SILVER)
CARPENTER'S
GLUE
SUPPLIES
In addition to the parts included in the kit you will also need:
HELPFUL HINT:
IF NOSE CONE/COUPLER FIT IS. . .
TOO
TIGHT
TOO
LOOSE
ADD
MASKING TAPE.
SAND FOR FIT.
Green Engine
Block (1)
(30162-2)
Body Tube BT-70 (1)
(30413)
Engine Mount Tube (1)
BT-20
(30329)
Mylar Retainer
Ring (1)
(30168)
Launch Lugs (2)
(38175)
Engine Hook (1)
(35021)
Cluster Bombs (4)
(72662)
Shock Cord
1/4" x 18" (1)
(38380)
Orange Streamers (4)
(60034)
Assembled 12"
(30 cm)
Parachute (1)
(35801)
Centering Ring
Card (1)
(60562)
Die-Cut Balsa
Fins (2)
(32217)
Plastic Nose Cone
Half A (1)
(60558)
EST 2055/1246
Keep for Future Reference
Locate the parts shown below and lay them out on the table. DO
NOT USE THE DRAWINGS TO ASSEMBLE YOUR ROCKET.
SHOCK CORD
MOUNT
SECTION
3
SECTION
2
SECTION
1
Yellow Spacer Tool (1)
(35003)
Clay Weights (2)
(85705)
Plastic Nose Cone
Half B (1)
(60559)
Plastic Tail Cone
Half A (1)
(60560)
Plastic Tail Cone
Half B (1)
(60561)
Decal Sheet (1)
(60563)
Enduring Freedom
Sticker (1)
(60586)
www.estesrockets.com
Estes® Industries
1295 H Street
Penrose, CO 81240
PRINTED IN CHINA
FLYING MODEL ROCKET
KIT INSTRUCTIONS
PARTS
ASSEMBLY TIP
Read all instructions before
beginning work on your model.
Make sure you have all parts
and supplies.
TEST FIT ALL PARTS TOGETHER
BEFORE APPLYING ANY GLUE!
If any parts don't fit properly, sand as
required for precision assembly.
SCISSORS
PENCIL
RULER
FINE SAND
PAPER
(#400-600 GRIT)
MASKING
TAPE
PLASTIC
CEMENT
MODELING
KNIFE
SPRAY
PRIMER
(WHITE)
SPRAY PAINT:
(OLIVE DRAB,
LIGHT GRAY)
SPRAY DULL
COAT
(OPTIONAL)
PAINT PEN
(SILVER)
CARPENTER'S
GLUE
SUPPLIES
In addition to the parts included in the kit you will also need:
HELPFUL HINT:
IF NOSE CONE/COUPLER FIT IS. . .
TOO
TIGHT
TOO
LOOSE
ADD
MASKING TAPE.
SAND FOR FIT.
Green Engine
Block (1)
(30162-2)
Body Tube BT-70 (1)
(30413)
Engine Mount Tube (1)
BT-20
(30329)
Mylar Retainer
Ring (1)
(30168)
Launch Lugs (2)
(38175)
Engine Hook (1)
(35021)
Cluster Bombs (4)
(72662)
Shock Cord
1/4" x 18" (1)
(38380)
Orange Streamers (4)
(60034)
Assembled 12"
(30 cm)
Parachute (1)
(35801)
Centering Ring
Card (1)
(60562)
Die-Cut Balsa
Fins (2)
(32217)
Plastic Nose Cone
Half A (1)
(60558)
EST 2055/1246
Keep for Future Reference
Locate the parts shown below and lay them out on the table. DO
NOT USE THE DRAWINGS TO ASSEMBLE YOUR ROCKET.
SHOCK CORD
MOUNT
SECTION
3
SECTION
2
SECTION
1
Yellow Spacer Tool (1)
(35003)
Clay Weights (2)
(85705)
Plastic Nose Cone
Half B (1)
(60559)
Plastic Tail Cone
Half A (1)
(60560)
Plastic Tail Cone
Half B (1)
(60561)
Decal Sheet (1)
(60563)
Enduring Freedom
Sticker (1)
(60586)
