OPERATOR’S
MANUAL
CMA-9000 FLIGHT MANAGEMENT SYSTEM
Page
A-225
November 19, 2009
REF [1L]:
This field displays the reference identifier. Successively pressing this button with an empty
scratchpad, the reference selection changes between the system position (FMS – default state = active nav),
INS/GPS, GPS, the joystick prompt (JOYSTICK), and a waypoint identifier entry prompt (-----) (in this order).
•
When
the
system
is used as the reference, the CMA-9000 FMS active navigation mode is displayed in
parenthesis next to it.
•
When the CMA-9000 FMS - INS/GPS navigation is used as the reference, INS/GPS is displayed in
parenthesis next to it.
•
When the CMA-9000 FMS - GPS navigation is used as the reference, GPS is displayed in parenthesis next
to it.
•
When
the
entry
prompt is selected, this button allows the pilot to specify a waypoint ID via the scratchpad.
•
When
the
joystick
prompt is selected, a prompt appears to specify the true joystick marked position by
entering the waypoint ID at LSK 3L or the position coordinates at LSK 3R.
•
When a position is specified via field at LSK 2R, the reference ID is dashed.
NOTE: When this softkey is pressed, the entry prompt data fields are reset.
ACCUR (2L):
This field displays the reference’s accuracy. When the reference is a fix location or joystick
derived position, the value is set to the configurable option value.
BRG/DIST [1R]:
This optional prompt is displayed when a waypoint ID was entered as the reference. This
field can be used to offset the identifier position by entering the desired bearing and range. Pressing [CLR], then
the LSK key in this field forces the offset back to its default (no offset).
UPDATE POS [2R]:
This field displays the final position which be used to perform the update. It can also be
used to enter coordinates via the scratchpad. When a position is manually entered, the REF prompt becomes
dashed. When an offset is entered, the update position corresponds to the offset reference’s position.
TRUE JOY POS [3R]:
{WEATHER RADAR or AHCAS EFIS configured} This field is displayed only when the
joystick prompt is selected. This field allows the true joystick position coordinates to be entered via the
scratchpad.
TRUE JOY POS ID [3L]:
{WEATHER RADAR or AHCAS EFIS configured} This field is displayed only when
the joystick prompt is selected. This field allows the true joystick position ID to be entered via the scratchpad.
INS/DVS or INS/GPS [4L]:
{SIGMA50H EGI configured} This field selects/deselects the INS/GPS and
INS/DVS navigators. The INS/GPS is displayed only when hybridization is off. This prompt is available for
selection only if a valid update position was entered and the MARK key was pressed. When selected, the
navigators are highlighted in white. The “CHECK UPDATE” advisory message appears if a sensor is selected
whose accuracy is smaller than its position difference with the update position.
INS [4L]:
{IRS or LN_100GT EGI configured} This field selects/deselects the INS navigator. When the
LN_100GT EGI is installed, this prompt is available for selection only if a valid update position was entered and
the MARK key was pressed. When the IRS is installed, this prompt is available for selection only if in Inertial
navigation mode. If a valid update position was entered and if the MARK key was pressed. When selected, the
navigator is highlighted in white. The “CHECK UPDATE” advisory message appears if a sensor is selected
whose accuracy is smaller than its position difference with the update position.
DVS [5L]:
{DVS configured} This field selects/deselects the DVS navigator. This prompt is available for
selection only if a valid update position was entered and the MARK key is pressed. When selected, the
navigator is highlighted in green. The “CHECK UPDATE” advisory message appears if a sensor is selected
whose accuracy is smaller than its position difference with the update position.
This page is printed under user's responsibility
and must not be retained for reference