OPERATOR’S
MANUAL
CMA-9000 FLIGHT MANAGEMENT SYSTEM
Page
A-99
November 19, 2009
ATOS TARGET [2L,2R]:
Displays ATOS Target position. Selection of 2L or 2R line key will place the ATOS
Target position in the scratchpad. A time stamp is displayed above this line, showing the last time an ATOS Target
position has been received. If the ATOS Target position time is the most recent (compared to the Radar Target
position), then its time is displayed in reverse video white. When the UTC time is selected (via SETUP 1/1 page),
a "z" is located after the time to indicate that time is Zulu (UTC). If the time selected is LOCAL, the "z" is not
displayed. This field and title is only displayed when the ATOS is configured.
ATOS TRANSFER STATUS (3L):
This field displays the ATOS flight plan transfer status when the ATOS
equipment is configured, otherwise this field is blank. The status could be one of the following:
1 - IDLE: Default status when no transfer request has been initiated by the ATOS; or
2 - REQUESTED: When the ATOS equipment informs the FMS that it is ready for flight plan transfer; or
3 - IN PROGRESS: When the START prompt has been pressed and the flight plan transfer is in progress; or
4 - COMPLETED: When a flight plan transfer from the ATOS has been completed successfully; or
5- FAILED: When the flight plan transfer has failed.
RADAR ID X-REF [5L]:
Access to the RADAR ID X-REF 1/1 page if FIAR 1500B Radar is configured,
otherwise, this prompt is not displayed.
NEW USER WPT [6L]:
Access to the USER WPT 1/2 page and transfers the Radar target or the ATOS target
position (the most recent one is selected) into the position field of that page. When the ATOS target is selected,
the REF WPT ID on the user waypoint page is set to "ATOS" and the reference position is set to the ATOS target
position. If the Radar target is selected, the REF WPT ID on the user waypoint page is set to "RADAR" and the
reference position is set to the RADAR target position. When no target (RADAR or ATOS) are displayed on the
page, this prompt is blanked.
START [3R]:
This prompt is displayed when the ATOS equipment requests a flight plan transfer to the FMS.
When this prompt is pressed, the flight plan transfer is initiated from the ATOS and the prompt disappears until a
new ATOS transfer request is received from the ATOS. This prompt is only available if the ATOS equipment is
configured. When this prompt is pressed while a route (active or inactive) modification is in progress, the transfer
is prevented and the message !MOD IN PROGRESS is displayed in the scratchpad.
DES+SAR [6R] or TACTICAL [6R]:
When TACT key is configured, the DES+SAR prompt is replaced by
TACTICAL. In this case, the prompt gives access to the TACTICAL page instead of the DES+SAR page. Access
to the DES+SAR 1/Y (or TACTICAL 1/Y) page. When there is no data in the scratchpad, selection of this key will
create a temporary waypoint with the Radar Target or the ATOS Target position (the most recent one received is
selected) and the temporary waypoint ID is entered in the REF ID field of the DES+SAR 1/Y (or TACTICAL 1/Y)
page. When there is a valid position in the scratchpad, selection of this key will create a temporary waypoint and
enter temporary waypoint identifier in the REF ID field of the DES+SAR 1/Y (or TACTICAL 1/Y) page.
When the inactive route is in modification, instead of accessing the DES+SAR 1/Y (or TACTICAL 1/Y) page, this
prompt gives acess to the INACT DES+SAR 1/X 1/Y (or INACT TACTICAL 1/Y) page.
This page is printed under user's responsibility
and must not be retained for reference
