Essentim Scope 4 User Manual Download Page 5

Notes

Warning: This symbol is a warning. It describes a dangerous situation or indicates

safety risks.

Note: This symbol indicates important information.

This symbol of a crossed-out wheeled bin indicates that this device contains

electronic components and should not be disposed of with household waste in
accordance with Directive 2002/96 / EC (WEEE).

Legal information

No part of this document may be reproduced, electronically reproduced or distributed in any

form without a written permission of essent

im

GmbH.

essent

im

GmbH assumes no liability for any errors or omissions. The determination of valid

measurement results, conclusions and measures derived therefrom are solely the sole

responsibility of the user.

essent

im

GmbH does not guarantee the correctness of the

measured values   or measurement results. Furthermore,

essent

im

GmbH assumes no liability

for errors or damage resulting from the use of the measured values   determined.

Reserve technical changes. All rights reserved.

essent

im

GmbH

Warranty and liability

The device complies with the essential health and safety requirements of the relevant EU
regulations and has been factory tested for proper function. When claiming the warranty, the

device number must be indicated (see product label on the device). Non-observance of the

manufacturer's instructions or any legal requirements or unauthorized modifications to the

equipment or unauthorized replacement of any part or accessory may significantly affect the

electrical safety of this product and may void the warranty. Any liability, property damage or

personal injury resulting from the device being used contrary to the instructions in this user

manual is excluded. Technical and formal design modifications due to continuous

development and product improvement are reserved at any time without prior notice. For

damages resulting from improper use, no liability is assumed and warranty claims expire as

well.

5

user manual scope - version 1.1

Summary of Contents for Scope 4





















Reviews: