background image

Information to User

 

This device complies with part 15 of the FCC Rules. Operation is subject to the 

condition

 that t

his device 

does

 not cause harmful interference

.

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to  Part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful  interference in a residential 

installation. This equipment generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, may cause harmful 

interference to  radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can  be determined by 

turning the equipment off and on, the user is encouraged to try to correct the 

interference by one of the following measures: 

- Reorient or relocate the receiving antenna. 

- Increase the separation between the equipment and receiver. 

- Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected. 

- Consult the dealer or an experienced radio/TV technician for help. 

FCC Caution: Any changes or modifications not expressly approved by the party 

responsible for compliance  could void the user's authority to operate this 

equipment. 

This transmitter must not be co-located or operating  in conjunction with any 

other antenna or transmitter. 

This equipment complies with FCC radiation exposure limits set forth for an 

uncontrolled environment. 

Summary of Contents for ES310


























Reviews: