ESD C.2067.02 Hardware Manual Download Page 39

Page: 39 / 53

Connector Assignment

6.4 Power-over-CAN (CAN-AIR2-PoC only)

DANGER

The CAN-AIR/2-PoC must be supplied by a limited current source (see chapter 5.1)!

DANGER
Device of protection class III

The CAN-AIR/2-PoC may only be driven by power supply current circuits, that are
contact protected. A power supply, that provides a safety extra-low voltage (SELV or
PELV) according to EN 60950-1, complies with this conditions.

Functional earthing is allowed, but must not conflict with the safety considerations of the
system.

INFORMATION

The Power-over-CAN functionality is only provided in the CAN-AIR/2-PoC.

Device connector: 9-pin DSUB connector, male

Pin Position:

Pin Assignment:

Signal

Pin

Signal

CAN_GND

reserved

CAN_L

CAN_H

CAN_GND

reserved

M24

P24

Shield

Signal Description:

CAN_L, CAN_H...

CAN signal lines

CAN_GND..

reference potential of local CAN physical layer

Shield...

Shielding (connected with case of the 9-pin DSUB connector)

reserved...

reserved for future applications, do not connect!

P24...

optional 24V-power supply voltage, typical 24VDC (min. 8V, max. 32V)

M24...

reference potential of the 24V power supply voltage.

CAN-AIR/2

Hardware Manual • Doc. No.: C.2067.21 / Rev. 1.5

Page 39 of 53

1 2 3 4 5

6 7 8 9

Summary of Contents for C.2067.02






















































Search results

Summary of Contents for C.2067.02

Reviews:

Related manuals for C.2067.02

Brands by name

Popular brands

ESD C.2067.02, Hardware Manual

Search results

Summary of Contents for C.2067.02

Reviews:

Related manuals for C.2067.02

Brands by name

Popular brands