Erreka VULCAN D User Manual Download Page 1

English

VULCAN_TOC.fm - 

21/2/13

VULCAN D Hydraulic operator

41

INDEX

General safety instructions

42

Symbols used in this manual__________________________________ 42
Importance of this manual ___________________________________ 42
Envisaged use ______________________________________________ 42
Installer's qualifications ______________________________________ 42
Automatic safety elements ___________________________________ 42

Description of the product

43

Elements of the complete installation __________________________ 43
General features of the operator ______________________________ 44
Main operator parts_________________________________________ 44
Technical features of the operator _____________________________ 45
Manual operation __________________________________________ 46
Declaration of conformity ____________________________________ 46

Unpacking and contents

47

Unpacking_________________________________________________ 47
Content___________________________________________________ 47

Installation

48

Required tools _____________________________________________ 48
Initial conditions and checks__________________________________ 48
Installing the operator _______________________________________ 49
Final preparation ___________________________________________ 57

Maintenance and diagnosis of failures

58

Maintenance_______________________________________________ 58
Failure diagnosis____________________________________________ 58
Spare parts ________________________________________________ 59
Scrap _____________________________________________________ 59

Summary of Contents for VULCAN D




















Reviews: