SQUIDS
®
BARCODE
SCANNER ADAPTOR
WWW.ERGODYNE.COM // 800 225 8238
The Squids® Barcode Scanner Adaptor Strap is designed for ease-of-use while reducing
the risk of dropped barcode scanners (refer to Using A Tethering System instructions).
WARNINGS: ALL WARNINGS AND INSTRUCTIONS MUST BE READ AND UNDERSTOOD
BEFORE USING THIS PRODUCT. FAILURE TO DO SO MAY RESULT IN PROPERTY
DAMAGE, SERIOUS INJURY, OR DEATH.
• Never exceed the allowable weight capacity for any Tool Lanyard.
• Always inspect tool lanyard prior to, and after, each use (refer to inspection
instructions).
• Do not wrap a Tool Lanyard around sharp or rough edges.
• Never modify or alter your Tool Lanyard.
• Never modify a tool that could result in manufacturer guideline deviation.
• Do not use this product if it interferes with the tool’s safe working condition.
• Use extra precaution around moving machinery or parts, electrical hazards, chemical
hazards or other apparent hazards.
INSTRUCTIONS FOR ATTACHING 3136 BARCODE SCANNER ADAPTOR STRAP TO
BARCODE SCANNER
The 3136 can be used independently as a strap or together with the 3135 scanner belt
hook lanyard as a system.
1. The 3136 barcode scanner adaptor strap attaches to the barcode scanner using two
small loop attachments on the end of the modular female buckles. Detach the female
buckle ends from the rest of the barcode scanner adaptor strap for installation [fig. 1]
2. Take the small loop attachment on the modular female buckle and thread it through
the captive hole in the bottom of the barcode scanner gun. [fig. 2]
- If necessary, use a small screwdriver or hex key to help thread the loop attachment
through the captive hole on the barcode scanner [fig. 3]
3. Cinch the loop attachment to the captive hole in the barcode scanner by pulling the
female buckle end through the loop and pulling the loop tight to remove slack. [fig. 4]
4. Repeat steps 2 and 3 using the captive hole located near the rear bottom of the
barcode scanner. Attaching both loop attachments completes the strap system.
[fig. 5].
* For further instructions, watch the product video on www.ergodyne.com.
INSPECTING A BARCODE SCANNER ADAPTOR STRAP
Inspect a tethering system before and after each use. All equipment should be regularly
inspected by a competent person. Ensure the tethering system is properly attached to the
tool and is not damaged. Before each use, check the following:
• Examine webbing, stitching and other soft materials for cuts, tears, heat trauma, frays
or other damage.
STORAGE AND CARE
Store tool attachments in a clean, dry location, away from direct sunlight. Clean
attachments using mild soap and water, and then air dry.
DISCLAIMER
In no event, shall Tenacious Holdings, Inc., be liable for any direct, indirect, punitive,
incidental, special, or consequential damages arising out of, or associated with, the misuse
of Squids® tethering system components (tool lanyards or attachments).
WARRANTY
We stand behind everything we make and guarantee our products are free of defects in
materials and workmanship to the original purchaser for the product’s lifetime. Damage,
abuse, and/or normal wear are not covered. Questions? Call Ergodyne at +1-651-642-9889
(8 a.m. - 5 p.m. CST) or 800-225-8238.
La correa de adaptador Squids® se ha diseñado para facilitar el uso del escáner de códigos
de barras y reducir el riesgo de que se caiga (consulte las instrucciones sobre Cómo
utilizar un sistema de sujeción).
ADVERTENCIAS: ANTES DE UTILIZAR ESTE PRODUCTO, DEBE LEER
ATENTAMENTE TODAS LAS ADVERTENCIAS E INSTRUCCIONES. SI NO LO HACE,
PODRÍA DAÑAR EL MATERIAL Y SE PODRÍAN PRODUCIR LESIONES GRAVES O
INCLUSO LA MUERTE.
• No se debe exceder nunca el peso máximo permitido de ningún cordón de seguridad
para herramientas.
• Inspecciónelo siempre antes y después de cada uso (consulte las instrucciones sobre
inspección).
• No se debe colocar alrededor de bordes afilados o ásperos.
• No se debe modificar ni alterar nunca.
• No se debe modificar nunca ninguna herramienta de forma que se incumplan las
instrucciones del fabricante.
• No utilice este producto si interfiere con las condiciones de uso seguro de la
herramienta.
• Tenga especial cuidado en entornos con maquinaria o piezas en movimiento, o
cuando existan riesgos eléctricos, químicos o de otra naturaleza.
INSTRUCCIONES PARA ENGANCHAR LA CORREA DE ADAPTADOR AL ESCÁNER DE
CÓDIGOS DE BARRAS 3136
El modelo 3136 se puede utilizar de forma independiente como una correa o junto con el
cordón de seguridad con gancho de cinturón 3135 como un sistema.
SPANISH // ESPAÑOL
FIG. 2
FIG. 3
FIG. 4
FIG. 5
FIG. 1
