background image

 

EG_GenPro2xe_1003_UG_005_UK 

Page 44 / 63

 

 

Descriptions and non-contractual illustrations in this document are given as an indication only. 

 

ERCO&GENER reserves the right to make any modifications. 

Dct_427_00 

7.9 Audio 

The modem contains the EGM standard library (see the documents "EG_EGM_CL_xxx_yy" of ERCO & 

GENER) in this case, the audio interface is standard to connect an equipment like a telephone handset. 

The echo cancelation (command 

AT$MICAEC

) and noise reduction features are also available in order to 

improve the audio quality in the case of free-hand applications. 

The audio interface is standard to connect a telephone handset (the command 

AT$VSELECT

 allows the 

Handset selection, see the document "EG_EGM_CL_xxx_yy" of ERCO & GENER). 

ERCO & GENER advises the use of the cable DATA/AUDIO Sub D 9pts Fem / Sub HD 15pts Male / RJ9 

(order code 4404000205) and a telephone handset (order code 3153400000). 

 

Designation 

SUBD 9 F 

SUBD 15 M-HD 

DCD/Buzzer 1 

RXD 2 

TXD 3 

DTR 4 

GND 5 

DSR 6 

RTS 7 

12 

CTS 8 

11 

RI/3.8V 9 

13 

 

RJ9  

Micro + 

10 

Speaker - 

15 

Micro - 

 

 

Summary of Contents for GenPro 22e
































































Reviews: