manualshive.com logo in svg

Epygi Quadro 16xa, Installation Manual

Share
Download
Epygi Quadro 16xa Installation Manual Download Page 17

Quadro Manual I: Installation Guide 

Step 1: Installing the Quadro 

 

 

Quadro2x, 2xi, Quadro4x, 4xi, 4xa, 4xia, 4xs, 4xis, Quadro16x, 16xi, 16xa, 16xia, 16xs, 16xis; (SW Version 3.0.x)

 16 

 

Connecting the Hardware 

• 

Quadro4x behind a router 

Quadro2x and Quadro16x are connected accordingly. 

 

 

Fig. I-12: Installation: Quadro4x behind a router 

 

• 

Quadro4x used as Internet access router 

 

Quadro2x and Quadro16x are connected accordingly. 

 

 

Fig. I-13: Installation: Quadro4x used as an Internet Access Router 

 

• 

Quadro4xi used as Internet access router 

 

All Quadro ISDN IP PBXs are connected accordingly. They also may be con-
nected with its Ethernet WAN port to a router (see above) and additionally, the 
ISDN ports of all Quadro devices may be joined to a PBX with ISDN interfaces.  

 

 

Fig. I-14: Installation: Quadro4xi used as an Internet Access Router 

 

Summary of Contents for Quadro 16xa

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands