background image

Date : 

1. MOVEMENT DIMENSIONS

Outside diameter

φ

27.60mm (12H-6H) 

×

 24.00mm (3H-9H)

Casing diameter

φ

27.00mm (12H-6H)

Total height

3.7mm (including battery)

2. TIME STANDARD

Type of quartz oscillator

Tuning fork

Frequency of quartz oscillator

32,768 Hz

Accuracy

±

20 seconds per month (on wrist)

Operating temperature range

5

 to 

50

Regulation device

Nil (Pre-adjusted)

3. INDICATOR / FUNCTIONS

3 Hands

Hour / Minute / Second chronograph (Center)

Small hands

1/100 second chronograph / 1/10 second chronograph (12H)
40 minute chronograph (6H) / Small second (9H)

Calendar

Instant setting device for date calendar

Reset switch
System-reset switch
Power depletion warning function (BLD)

(Small second hand moves at 2-second intervals)

Chronograph

4. FEATURES

Jewels

0 Jewels

Anti-magnetism

Over 1600A/m (Direct current magnetic field)

Maximum unbalance of hands

Small second hand

: 0.03

μ

N

m

1/100 second chronograph hand

: 0.005

μ

N

m

1/10 second chronograph hand

: 0.025

μ

N

m

40 minute chronograph hand

: 0.03

μ

N

m

Second chronograph hand

: 0.06

μ

N

m

Minute hand

: 0.70

μ

N

m

Moment of Inertia 

Second chronograph hand

: less than 0.2

 μ

g

5. BATTERY 

Type / Size

Silver oxide battery /

φ

9.5mm 

×

 t 2.73mm

Recommended battery

SR927W 

Nominal voltage

1.55 V

Battery life

Approx. 3 years
(120 minutes chronograph operation per day)

Driving current consumption

Approx. 0.80

μ

A

Operation stopping voltage

0.9 V

6. SEPARATED PARTS (Parts code)

Hand setting stem

0351584 (Standard)  or  0351585 (Long)

Holding ring for dial

0866650 (Standard)  or  0866789 (Special)

Battery

SR927W 

Magnetic shield plate

4259519

A.C. comment seal

0110705

7. TEST OF ACCURACY

Equipment to be used

SEIKO quartz tester QT-99, QT2100
Greiner quartz timer-C , Witschi Q-tester 4000

Duration of measurement

10 seconds

Microphone to be used

Electromagnetic detection type

All specifications are subject to change without notice.

Cal.

Rev. :  01

30/Jan./'15

YM82A

Specifications

Analog Quartz 12''' Center second Chronograph Movement

The chronograph can measure up to 41 minutes in 1/100 second
increments, capable of timing 120 minutes.

P. 1 

Summary of Contents for YM82A


















Reviews: