7
Open the top covers and remove the protective film from the print head
and any tape and protective material inside.
8
Close the top covers.
9
Remove the tape from the front of the printer and the paper catch
basket.
10
Open the ink cover and remove any protective material inside.
Note:
Make sure to open all compartments and remove all tape and
protective materials from inside the printer before turning the printer on.
Otherwise, you may not be able to print.
Turn On and Configure
1
Connect the power cord to the back of the printer and plug the other
end into an outlet.
Note:
If you are using the SSD (Solid State Drive) or Adobe
®
Embedded Print
Engine options, make sure to install them in the expansion slots on the back of
the printer before turning the printer on. (The Adobe Embedded Print Engine is
an option for the SureColor P6570DE/P6570E; it is pre-installed for all other
models. The SSD unit is an option for all models.)
2
Press the power button on the control panel to turn on the printer.
3
Select your language, date, and time on the touchscreen.
Note:
• You can change these settings later using the product’s control panel. For
more information, see the online
User’s Guide
.
• If an error code appears, turn off the printer and check that no protective
material has been left inside.
4
Follow the instructions on the touchscreen to begin ink initialization.
Epson
®
SureColor
®
P6570D/P6570DE/P6570E/P8570D/P8570DL
Start Here
IMPORTANT: Before using this product, make sure you read these instructions
and the safety instructions in the online User’s Guide.
The illustrations show the SureColor P8570D, but the steps are the same for all
models, unless otherwise specified.
Choose a Location for the Printer
Choose a location for the printer that is near a wall outlet where the power cord
can be easily unplugged. Avoid places subject to rapid changes in temperature
and humidity. Also keep the printer away from direct sunlight, strong light, or
heat sources.
Make sure to place the printer on a flat, stable surface capable of supporting
approximately 275 pounds (124.7 kg) (SureColor P6570E), 291 pounds
(131.8 kg) (SureColor P6570D/P6570DE), 395 pounds (179 kg) (SureColor
P8570D), or 440 pounds (199.5 kg) (SureColor P8570DL) and with enough
space on all sides (see illustration below).
2.75 in.
(70 mm)
7.67 in.
(195 mm)
2.95 in.
(75 mm)
24.84 in.
(631 mm)
46.06 in.
(1170 mm)
Model
W
D1
(Roll Paper)
D2
(Cut Sheets/
Poster Board)
SureColor P8570D/P8570DL
78.46 in. (1993 mm)
44.48 in. (1130 mm)
157.48 in. (4000 mm)
maximum
SureColor P6570D/
P6570DE/P6570E
59.44 in. (1510 mm)
Note: If you are loading rigid poster board, the printer must be at least 30 inches
(762 mm) away from the wall.
Unpack and Place Printer
1
Make sure you have these items:
Printer
Ink cartridges (6)
(SureColor P6570D/
P6570DE/P6570E/P8570D)
Limited warranty
Power cord
Note:
Ink supply units (ink packs) not included with the SureColor P8570DL
model.
2
Remove the outer carton from the pallet and printer and carefully lift
the printer off of the pallet.
WARNING:
The printer requires four people to lift and move it. Make sure to
grip the printer as shown in the illustration.
3
Remove the protective plastic and all tape from the outside of the
printer.
4
Lock the front casters by pushing the tabs down.
5
Secure the two adjustable feet on the back of the printer.
Note:
Turn the adjustable feet by hand until they touch the floor. If you turn
them 180° or more after they touch the floor, print quality may decline.
6
Remove the protective film from the touchscreen.
Note:
The touchscreen will not operate if you do not remove the protective
film.
Install Ink Cartridges
(SureColor P6570D/
P6570DE/P6570E/P8570D)
Caution:
Keep the ink cartridges out of the reach of children and do not drink the ink.
Note:
• The printer is designed for use with Epson
®
cartridges only, not third-party
cartridges or ink.
• The cartridges included with the printer are designed for printer setup and not for
resale. After some ink is used for initializing, the rest is available for printing.
1
Open the ink cartridges and shake them as shown for 10 seconds, or
about 30 times.
Caution:
Do not touch the green chip on top of the cartridge. Doing so may
prevent normal operation and printing.
2
Open the ink cover.
3
Insert the cartridges in the slot for each color as described on the label
inside the ink cover. Push the cartridges in until they click.
Note:
Make sure all of the ink cartridges are properly inserted in the product;
otherwise printing is not possible.
4
Close the ink cover.
