manualshive.com logo in svg

Epson SureColor P-Series, Setup Manual

Share
Download
Epson SureColor P-Series Setup Manual Download Page 33

32

|

Configuring the printer for your network

5.

Double-click the firmware file that you downloaded.

Note: 

Make sure your printer is turned on and connected to your computer or network before you run the 

firmware file.

6.

Follow the on-screen instructions to install the new firmware on your printer.

Caution: 

Don’t turn off the printer while the firmware is updating. The printer automatically turns off when 

the firmware update is complete.

If you connected to your printer through a network, follow the instructions in the next section to 
configure the printer for your network.

Configuring the printer for your network

Once the printer is connected to your network, follow these steps to configure it:

1.

Turn on the printer.

2.

Start EpsonNet Config.

EpsonNet Config searches for all Epson printers on the network and displays the MAC address for 
each printer that it finds.

3.

Highlight the printer you want to configure and click 

Configuration

 to access the TCP/IP selection 

screen.

4.

If necessary, contact your network administrator for instructions on assigning an appropriate IP 
address. A static IP address is recommended.

EPSON and SureColor are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson 
Corporation. 

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective 
owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

© 2016 Epson America, Inc., 2/16

CPD-51060

Summary of Contents for SureColor P-Series



































Reviews:

No comments

Brands by name

Popular brands

Load more brands