Epson Stylus Pro 9700 Series User Manual Download Page 215

Page: 215 / 228

215

Control Panel Summary

215

Lights

See “Checking Error Messages and Lights” on page 176 for instructions on
responding to problems indicated by the printer lights.

Light

Description

Power

On: printer is turned on

Flashing: printer is printing or shutting down

Off: printer is turned off

Pause/reset

On: printer is paused, in Menu mode, or has an error

Off: printer is ready

Paper

On: no paper is loaded, paper is out, the selected
paper source does not match the printer driver
source, or the loaded paper is too thick for print head
cleaning

Flashing: paper is jammed or not loaded straight

Ink

On: an ink cartridge is expended, not installed, or not
compatible with the printer

Flashing: an ink cartridge is nearly expended

Paper release or
ePlaten

On: paper is released

Off: paper is locked in the printer

Summary of Contents for Stylus Pro 9700 Series





































































































































































































































Search results

Summary of Contents for Stylus Pro 9700 Series

Reviews:

Brands by name

Popular brands

Epson Stylus Pro 9700 Series, User Manual

Search results

Summary of Contents for Stylus Pro 9700 Series

Reviews:

Brands by name

Popular brands