Epson Stylus Pro 9700 Series User Manual Download Page 195

Page: 195 / 228

195

195

Environmental

Electrical

Check the label on the back of your printer for voltage information.

Operation

Storage

Temperature

50 to 95

(10 to 35

Print quality guarantee:
59 to 77

(15 to 25

–4 to 104

(–20 to 40

Humidity
(without
condensation)

20 to 80% RH

Print quality guarantee:
40 to 60%

5 to 85% RH
(stored in shipping
container)

Specification

Description

Input voltage range

90 V to 264 V

Rated frequency range

50 to 60 Hz

Input frequency range

49.5 to 60.5 Hz

Rated current

1.0 A at 120 V
0.5 A at 220 V

Power consumption

Epson Stylus Pro 7700:
Approx. 80 W
Approx. 14 W in low-power mode
Approx. 1 W or less in power off mode

Epson Stylus Pro 9700:
Approx. 85 W
Approx.14 W in low-power mode
Approx.1 W or less in power off mode

Appendix A:
Specifications

Summary of Contents for Stylus Pro 9700 Series





































































































































































































































Search results

Summary of Contents for Stylus Pro 9700 Series

Reviews:

Brands by name

Popular brands

Epson Stylus Pro 9700 Series, User Manual

Search results

Summary of Contents for Stylus Pro 9700 Series

Reviews:

Brands by name

Popular brands