Epson Stylus Pro 9000 Printer Manual Download Page 71

Page: 71 / 165

3-16

3-16

Maintaining and Transporting the Printer

Transporting the Printer

When you need to ship your printer, you should repack it using the original
box and packing materials. Follow these steps to prepare the printer for
shipping:

1. First turn off the printer and make sure the print head is in the home

(far right) position. If not, turn the printer back on, wait until the print
head moves to the home position, then turn off the printer.

2. Remove the following parts:

•

Ink cartridges

•

Power cord

•

Interface cable

•

Paper hammock

•

Roll paper spindles

•

All paper or other media

•

Optional auto take-up reel (if installed)

After you remove the ink cartridges, store them in separate, resealable
plastic bags.

3. Make sure the ink cartridge clamps are in the upright position (closed).

Leave the ink compartment cover open. Use tape to hold the cover and
the cartridge clamps in place. This automatically closes the ink valves.

Caution

If for any reason the
printer will not be level
during shipping, a service
technician must drain all
ink from the printer
before it is shipped.

Summary of Contents for Stylus Pro 9000






































































































































































Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands

Epson Stylus Pro 9000, Printer Manual

Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands