Epson Stylus Pro 9000 Printer Manual Download Page 153

Page: 153 / 165

C-26

C-26

Using EPSON Drivers and Utilities for Windows

Running Printer Utilities

The utilities included with your printer software let you run the following
maintenance procedures:

•

Nozzle check

•

Print head cleaning

•

Print head alignment

•

Speed and progress configuration

Running Nozzle Check and Head Cleaning Utilities

The nozzle check prints a pattern of dots that lets you see if any print head
nozzles are clogged. If any dots are missing from the pattern, you can run a
head cleaning cycle to clear the nozzles.

Follow these steps:

1. Click

Start

, point to

Settings

, then select

Printers

. Right-click the

EPSON Stylus Pro 9000

9500

icon and select

Properties

. Or,

access the Main Printer Properties dialog box.

2. Click the

Utility

tab. You see the Utility menu:

Click to run
nozzle check.

Click to run head
cleaning utility.

Note

You can also access the
Status Monitor 2 Printer
Status window from this
menu.

Summary of Contents for Stylus Pro 9000






































































































































































Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands

Epson Stylus Pro 9000, Printer Manual

Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands