Epson Stylus Pro 9000 Printer Manual Download Page 125

Page: 125 / 165

B-24

B-24

Using EPSON Drivers and Utilities for Macintosh

Running Print Head Utilities

The utilities included with your printer software let you run the following
maintenance procedures from your computer:

•

Nozzle check

•

Print head cleaning

•

Print head alignment

Running Nozzle Check and Head Cleaning Utilities

The nozzle check prints a pattern of dots that lets you see if any print head
nozzles are clogged. If any dots are missing from the pattern, you can run a
head cleaning cycle to clear the nozzles.

Follow these steps:

1. Click the utility button

on the Print or Page Setup dialog box. You

see the Utility menu:

2. Click the button for the utility you want to run.

3. Follow the instructions on the screen to complete the process. For more

information, see Chapter 3.

Click to run
nozzle check.

Click to run head
cleaning utility.

Summary of Contents for Stylus Pro 9000






































































































































































Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands

Epson Stylus Pro 9000, Printer Manual

Search results

Summary of Contents for Stylus Pro 9000

Reviews:

Related manuals for Stylus Pro 9000

Brands by name

Popular brands