manualshive.com logo in svg

Epson Stylus Pro 7000 Series, Printer Manual

Share
Download
Epson Stylus Pro 7000 Series Printer Manual Download Page 44

2-10

2-10

|

Handling Paper

6. Holding the bottom edge of the paper, turn the roll back to remove the 

slack. Then align the paper with the two rows of holes. 

7. Pull the paper set lever all the way up, then close the roll paper cover. 

PRESS PAUSE BUTTON

 appears on the control panel display.

If you’re using Auto Cut and the edge of the paper is uneven, press 

Cut/Eject

 to recut the edge.

8. Press the 

Pause

 button. The print head moves and the paper feeds into 

printing position automatically. 

READY

 appears on the control panel 

display. (Even if you don’t press 

Pause

, the paper and printer will move 

into printing position automatically after 10 seconds.)

Caution

To avoid damaging the 
printer, never move the 
paper set lever while the 

Operate

 or 

Pause

 light is 

flashing.

Summary of Contents for Stylus Pro 7000 Series




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands