Epson Stylus Pro 7000 Series Printer Manual Download

Page: 28 / 147

1-12

1-12

Connecting Your Printer and Installing Drivers

Checking USB Installation (Windows 98)

If you’re using a USB connection, it’s a good idea to confirm that the driver
is set up correctly after you install it. Follow these steps:

1. Click

Start

, point to

Settings

, and click

Printers

. Make sure your

EPSON

Stylus Pro 7000

icon appears in the Printers window.

2. Right-click the icon, then click

Properties

3. Click the

Details

tab and note what is displayed under

Print to the

following port.

You should see

EPUSBx: (EPSON Stylus Pro 7000)

. If you don’t see

the correct port displayed, see Chapter 7 in this guide or
“Troubleshooting” in the electronic

Reference Guide

on your printer

software CD-ROM.

Setting Up Printer Sharing in Windows 95 and 98

First, you need to set up the printer as a shared printer on the computer to
which it is connected. Then, you must specify the network path to the
printer from each computer that will use it.

Setting up the printer as a shared printer

Follow these steps to share a printer that is connected directly to your
computer with other computers on a network.

1. Click

Start

, point to

Settings

, then click

Control Panel.

2. Double-click

Network

3. Click the

File and Print Sharing

button. You see the following:

Summary of Contents for Stylus Pro 7000 Series




















































































































































Search results

Summary of Contents for Stylus Pro 7000 Series

Reviews:

Related manuals for Stylus Pro 7000 Series

Brands by name

Popular brands

Epson Stylus Pro 7000 Series, Printer Manual

Search results

Summary of Contents for Stylus Pro 7000 Series

Reviews:

Related manuals for Stylus Pro 7000 Series

Brands by name

Popular brands