Epson Stylus Pro 7000 Series Printer Manual Download | Manualshive

Page: 23 / 147

background image

1-7

Connecting Your Printer and Installing Drivers

|

1-7

Installing the Software and Setting Up Printer
Sharing on a Macintosh

You need to install the drivers and utilities on any Macintosh that will print
to the EPSON Stylus Pro 7000. Make sure each Macintosh meets the
minimum system requirements. Then follow the procedure for installing the
software. Depending on your network configuration, you may also want to
set up printer sharing.

Checking System Requirements

The memory requirements listed in the following table are for printing a
23

×

33-inch

full-page color image. Requirements may vary, depending on

the size, complexity, and resolution of your images.

Installing the Software

Before you start, turn off all virus protection programs. See your anti-virus
software documentation for instructions. Then follow these steps to install
the printer software:

1. Insert the printer software CD-ROM.

2. Open the

Installer

folder and double-click the icon. Then follow the

instructions on the screen.

3. When you see the “installation complete” message, click

Restart.

4. After you restart, make sure you open the Chooser and select the printer.

System requirements

Component

Minimum

Recommended

Processor

PowerPC

300 MHz G3 or higher processor

OS

System 8.5.1

System 9 recommended for
best USB support

Available
memory

14MB (foreground printing)
23MB (background printing)

128MB (total)

Hard drive
space

10MB free for installing the
software

2GB recommended

CD-ROM

Double-speed CD-ROM drive

Quad-speed or faster

«
...
21
22
23
24
25
...
»

Summary of Contents for Stylus Pro 7000 Series




















































































































































Reviews:

No comments

Related manuals for Stylus Pro 7000 Series

imagePROGRAF iPF8400

Brand: Canon Pages: 157

Brand: Canon Pages: 91

CLP 510N - Color Laser Printer

Brand: Samsung Pages: 270

Bixolon SRP-270

Brand: Samsung Pages: 13

Brand: QMS Pages: 2

INFOPRINT HI-LITE COLOR 4005-HC2

Brand: IBM Pages: 10

5550N - Phaser B/W Laser Printer

Brand: Xerox Pages: 16

Brand: Ricoh Pages: 288

ECOSYS FS-C2126MFP

Brand: Kyocera Pages: 206

C11C418001 - Stylus C60 Inkjet Printer

Brand: Epson Pages: 64

C11C417001 - Stylus Photo 820 Color Inkjet Printer

Brand: Epson Pages: 2

C11C417001 - Stylus Photo 820 Color Inkjet Printer

Brand: Epson Pages: 2

C11C294131BZ - LX 300+ B/W Dot-matrix Printer

Brand: Epson Pages: 100

C117001-N - DFX 5000+ B/W Dot-matrix Printer

Brand: Epson Pages: 186

Brand: Oki Pages: 15

C11C498001 - Stylus Photo 825 Inkjet Printer

Brand: Epson Pages: 2

Brand: Muratec Pages: 6

Brand: Muratec Pages: 188

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands