Epson Stylus Pro 7000 Series Page 120 Printer Manual Download

Page: 120 / 147

7-10

7-10

Resolving Problems

•

Make sure the printer is not located in a brightly lit area. The paper
sensor may not be able to operate correctly.

•

Make sure the

Print Mode

Media Type

setting is correct for the

media you’re printing on.

•

Make sure the platen gap setting is correct for the paper or media you’re
printing on. See page 2-18 for more information.

•

If you’re not using EPSON media, make sure you register and select
your paper’s thickness. See page 2-21 for more information.

Solving Roll Paper Ejection Problems

If you are using the printer without the stand, tightly wound roll paper may
feed out with a curl. Extend the paper guides as shown below:

Summary of Contents for Stylus Pro 7000 Series




















































































































































Search results

Summary of Contents for Stylus Pro 7000 Series

Reviews:

Related manuals for Stylus Pro 7000 Series

Brands by name

Popular brands

Epson Stylus Pro 7000 Series, Printer Manual

Search results

Summary of Contents for Stylus Pro 7000 Series

Reviews:

Related manuals for Stylus Pro 7000 Series

Brands by name

Popular brands