Epson Stylus Pro 7000 Series Printer Manual Download | Manualshive

Page: 107 / 147

background image

6-15

Maintaining and Transporting the Printer

|

6-15

Transporting the Printer

When you need to ship your printer, you should repack it using the original
box and packing materials. Follow these steps to prepare the printer for
transport:

1. Make sure the printer is turned on. Then remove all ink cartridges as

described on page 6-8.

2. Make sure the paper set lever is in the secured position and the lower

cover is closed. Then press the

Power

button to turn off the printer.

The print head moves to the home (far right) position.

TRANSPORT

PREP <number> %

appears on the display and the

Operate

light

flashes for a few minutes while the ink is drained. Then the light goes off
and the printer shuts down.

3. Remove the following parts:

•

Power cord

•

Interface cable

•

Roll paper spindle

•

All paper or other media

Push in the paper guides if necessary.

4. Install the carriage shipping restraint (packaging material).

Caution

To avoid spilling ink
inside the printer during
transportation, make
sure you remove the
cartridges and follow
these instructions for
draining the ink lines.

«
...
105
106
107
108
109
...
»

Summary of Contents for Stylus Pro 7000 Series




















































































































































Reviews:

No comments

Related manuals for Stylus Pro 7000 Series

Brand: QMS Pages: 27

Brand: QMS Pages: 3

Brand: Canon Pages: 37

Brand: Unimark Pages: 38

imagePROGRAF GP-540

Brand: Canon Pages: 82

Brand: BIXOLON Pages: 31

Brand: Oki Pages: 126

Brand: A&D Pages: 16

Brand: QuickLabel Systems Pages: 122

Brand: Lexmark Pages: 9

Brand: Evolis Pages: 45

Brand: U-Line Pages: 33

Brand: Kashino Technology Pages: 72

Brand: Unisys Pages: 144

Brand: Riso Pages: 266

Brand: Infinite Peripherals Pages: 2

Quatro ID Card Printer

Brand: FARGO electronics Pages: 56

Brand: Printronix Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands