Epson Stylus Photo R290 Service Manual Download Page 81

Page: 81 / 125

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.4.9 EJ Frame Assy (Disassembling the Printer Mechanism)

Disconnect the PF Encoder FFC from the PF Encoder.

Remove the two screws, disengage the two hooks of the Cable Holder Frame
from the Front Frame and Main Frame, and remove the Cable Holder Frame.

Screw

: C.B.S. M3x6 (tightening torque: 7-9 kgf.cm)

(No.1)

(The numbers shown in the figure indicate the order of tightening the screws.)

Figure 4-73. Removing the Cable Holder Frame

Peel off the PF Encoder FFC from the back of the Cable Holder Frame.

Figure 4-74. Removing the PF Encoder FFC

Remove the screws on the right and left sides, and remove the Front Frame.

•

Screw

: C.B.S. M3x6 (tightening torque: 7-9 kgf.cm)

(No.1)

(The numbers shown in the figure indicate the order of tightening the screws.)

Figure 4-75. Removing the Front Frame

Release the CDR Sensor Cable from the cable guide of the EJ Frame Assy.

10.

Remove the EJ Frame Assy.

Figure 4-76. Removing the EJ Frame Assy

Hook

[Back Side]

Cable Holder Frame

PF Encoder FFC

[Back Side]

Cable Holder Frame

PF Encoder FFC

Reference Line

Cable Holder Frame

Front Frame

Positioning hole

and Guide Pin

EJ Frame Assy

Removal Direction

Cable Guide

CDR Sensor Cable

Summary of Contents for Stylus Photo R290






























































































































Search results

Summary of Contents for Stylus Photo R290

Reviews:

Epson Stylus Photo R290, Service Manual, Page: 81 / 125

Search results

Summary of Contents for Stylus Photo R290

Reviews: