Unpacking
Unpacking
Unpacking
Unpacking
1. Unpack the printer.
2. Attach the paper support and plug in the printer.
Installing the Ink Cartridges
Installing the Ink Cartridges
Installing the Ink Cartridges
Installing the Ink Cartridges
1. Press
P
button to turn on the printer.
2. Remove the ink cartridges from their protective bags, then
peel off the yellow tape.
.
c
Caution:
Do not shake the ink cartridges; this can cause leakage.
3. Install the ink cartridges as shown below.
c
Caution:
❏
Do not move the print head by hand; otherwise, you may damage the printer.
❏
Do not load paper until ink charging is complete.
Note:
Install both ink cartridges. The printer will not work unless both cartridges are installed properly.
4. Press the
e
ink cartridge replacement button.
The printer begins ink charging. It takes about
one and a half minutes
. While charging, the printer produces a variety of mechanical sounds.
This is normal. When the green lamp stops flashing, ink charging is complete.
c
Caution:
Do not turn off the printer during the ink charging process.
Note:
The ink cartridges packaged with your printer are partly used during initial setup. In order to produce high quality printouts, the print head in your
printer will be fully charged with ink. This one-off process consumes a quantity of ink and subsequent cartridge sets will last for their full rated life.
Safety Instructions
Read all of the instructions in this section when setting up and using your printer.
When choosing a place for the printer
❏
Avoid places subject to rapid changes in temperature and humidity. Also, keep the printer away from direct
sunlight, strong light, or heat sources.
❏
Avoid places subject to dust, shocks, and vibrations.
❏
Leave enough room around the printer to allow for sufficient ventilation.
❏
Place the printer near a wall outlet where the plug can be easily unplugged.
❏
Place the printer on a flat, stable surface that extends beyond the printer base in all directions. If you place
the printer by the wall, leave more than 10 cm between the back of the printer and the wall. The printer will
not operate properly if it is tilted at an angle.
❏
When storing or transporting the printer, do not tilt it, put it vertically or turn it upside down; otherwise, ink
may leak from the cartridge.
When choosing a power source
❏
Use only the type of power source indicated on the printer’s label.
❏
Be sure your AC power cord meets the relevant local safety standard.
❏
Do not use a damaged or frayed power cord.
❏
If you use an extension cord with the printer, make sure that the total ampere rating of the devices plugged
into the extension cord does not exceed the cord’s ampere rating. Also, make sure that the total ampere
rating of all devices plugged into the wall outlet does not exceed the wall outlet’s ampere rating.
❏
If you plan to use the printer in Germany, the building installation must be protected by a 10 or 16 amp
circuit breaker to provide adequate short-circuit protection and over-current protection for this printer.
When handling ink cartridges
❏
Do not open the ink cartridge packages until just before you install them.
❏
Keep ink cartridges out of the reach of children. Do not allow children to drink from or otherwise handle the
cartridges.
❏
Be careful when you handle used ink cartridges, as there may be some ink remaining around the ink supply
port. If ink gets on your skin, wash the area thoroughly with soap and water. If ink gets into your eyes, flush
them immediately with water. If discomfort or vision problems remain after a thorough flushing, see a doctor
immediately.
❏
Do not shake the ink cartridges; this can cause leakage.
❏
You must remove the yellow tape seals from the cartridges before installing them; otherwise, the cartridges
will become unusable.
❏
Do not remove the blue portion of the tape seal from the top of the cartridges.
❏
Do not remove the tape seals from the bottom of the cartridges.
❏
Do not touch the green IC chip on the side of the cartridge.
❏
The IC chip on this ink cartridge retains a variety of cartridge related-information, such as the amount of
ink remaining, so that a cartridge may be removed and reinserted freely. However, each time the cartridge
is inserted, some ink is consumed because the printer automatically performs a reliability check.
When using the printer
❏
Do not put your hand inside the printer or touch the ink cartridges during printing.
❏
Do not block or cover the openings in the printer.
❏
Do not attempt to service the printer yourself.
❏
Unplug the printer and refer servicing to qualified service personnel under the following conditions:
The power cord or plug is damaged; liquid has entered the printer; the printer has been dropped or the
cabinet damaged; the printer does not operate normally or exhibits a distinct change in performance.
❏
Do not insert objects through the slots in the printer.
❏
Take care not to spill liquid on the printer.
❏
Leave the ink cartridges installed. Removing the cartridges can dehydrate the printer head and may prevent
the printer from printing.
The contents may vary in certain locations.
The power cord comes attached in some countries.
Setup
printer
ink cartridges
paper support power cord
CD-ROM
Do not touch
this part.
Do not remove the blue portion.
Do not remove the tape seal
from the ink supply ports.
Installing the Printer Software
Installing the Printer Software
Installing the Printer Software
Installing the Printer Software
1. Press the
P
power button to turn off the printer. The green
light goes off.
2. Connect the printer and computer with a USB cable, then
insert the printer software CD into the CD-ROM drive.
3. Install the printer software.
Except where otherwise instructed, click or double-click the areas circled in red to proceed.
c
Caution:
Macintosh users turn off all virus protection programs before installing the printer software.
Note:
For information about installing the Photo Print Software, refer to the Photo Print Software Setup under User Guides on the printer software CD.
For Windows
For Max OS 8.6 to 9.X
For Mac OS X
1. Open the
Mac OS X
folder, then double-click the
SP830USeries_xxxx.pkg
icon. If the Authorization dialog box
appears, click the
icon (Mac OS X 10.1.x only), enter the
Password
or phrase
, then click
OK
.
2. Follow the on-screen instructions to install the software.
3. After installing the software and restarting the computer, press the
P
button
to turn on the printer.
4. Open the
Applications
folder on your hard drive, then open the
Utilities
folder and double-click the
Print Center
icon. Click
Add Printer
in the Printer List dialog box.
5. Select
EPSON USB
from the pop-up menu. Select
SP830U Series(USB)
in
the Product list, then select
All
from the Page Setup pop-up menu. Click
Add
.
6. Make sure the Printer List contains the printer(margin-type) options as
illustrated below. See the Reference Guide on the printer software CD-ROM
for more details.
7. Close Print Center.
Note:
When you print, be sure to match the
Format for
setting in the Page Setup dialog box and the
Printer
setting in the Print dialog box. Otherwise, the data may not be
printed correctly. See the Reference Guide for more details.
After installation is complete, see Printing Basics on the online
Reference Guide
for detailed information about printing from your
computer for the first time.
Accessing the Reference Guide
Accessing the Reference Guide
Accessing the Reference Guide
Accessing the Reference Guide
The
Reference Guide
provides detailed information about printing from a computer,
printer maintenance, problem solving, and safety.
For Mac OS X
1. Use the scroll bar to scroll down until the
English
folder appears,
then open it.
2. Open the
User Guides
folder, then open the
REF_G
folder.
3. Double-click the
INDEX.HTM
icon to open the online
Reference Guide
.
Follow the on-screen instructions.
If the installation dialog box does not
appear, double-click the SETUP file
on the CD-ROM.
1
2
Follow the on-screen instructions.
After installing the software and restarting
the computer, turn on the printer.
Select your printer and the port that your printer
is connected to, then close the chooser.
1
1
2
2
Windows
Mac OS 8.6 to 9.X
1
2
1
2
Mac OS 8.6 to 9.X
Setup
Cautions and Notes
Notes
contain important information and useful tips on the operation of your printer.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON
CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers. Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable
to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or
(excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION's operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by
SEIKO EPSON CORPORATION. SEIKO EPSON CORPORATION shall not be held liable for any damage resulting from electromagnetic interference that occurs from the use of any interface cables other than those designated as EPSON
Approved Products by SEIKO EPSON CORPORATION. EPSON is a registered trademark and EPSON Stylus is a trademark of SEIKO EPSON CORPORATION.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
General Notice:
Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
English
4041716-00
EUL
Color Ink Jet Printer
c
Cautions
must be observed to avoid damage to your equipment.
