Epson Stylus 1500 Service Manual Download Page 27

Page: 27 / 185

Setting Menus

The default setting menus are described in the table below.

Table 1-8. Default Settings

Menus

Settings

(underlines indicate factory default settings)

Print direction

Auto / Bi-D / Uni-D

Font

Draft / Roman / Sans Serif / Courier / Prestige / Script / Roman T /
Sans Serif H

Pitch

10 cpi / 12 cpi / 15 cpi / 17.1 cpi / 20 cpi / Proportional

I/F mode

Auto / Parallel / Serial

Auto I/F wait mode

10 seconds / 30 seconds

Software

ESC/P2 / IBM X24E

Auto CR
(IBM mode only)

On / Off

Alternate Graphics
Mode (AGM)
(IBM mode only)

On / Off

Character tables
(standard version)

Italic

PC 437

PC 850

PC 860

PC 863

PC 865

PC 861 BRASCII

Abicomp

Roman 8

ISO Latin 1

International
character set for
italic table

Italic U.S.A.

Italic France

Italic German Italic U.K.

Italic Denmark

Italic Sweden

Italic Italy

Italic Spain 1

Auto line feed

On / Off

Network I/F mode

Off: Used in standalone environment
On: Used in network environment

Zero slash

0 / Ø (with slash)

Page length for
continuous paper

11 inches 12 inches

8.5 inches

70/6 inches

Other

Skip over perforation

On / Off

Auto tear off

On / Off

Print mode

Plain paper (pure black) / Plain paper (composite black) /
EPSON premium ink jet paper / Transparencies

Paper roll

On / Off

Notes:

*1. Refer to Tables 1-9 and 1-10.

*2. This is selected when a value other than 11, 12, 8.5, or 70/6 inches has been placed

in EEPROM by the ESC | command.

*3. This mode is provided only for DOS users and is selected based on the paper type

Pure black and composite black are selected according to the printed result.

Printer Features

1-20

EPSON Stylus 1500 Service Manual

Summary of Contents for Stylus 1500


























































































































































































Search results

Summary of Contents for Stylus 1500

Reviews:

Brands by name

Popular brands

Epson Stylus 1500, Service Manual

Search results

Summary of Contents for Stylus 1500

Reviews:

Brands by name

Popular brands