manualshive.com logo in svg

Epson Stylus 1500, Service Manual

Share
Download
Epson Stylus 1500 Service Manual Download Page 26

Default Settings

This printer has user-selectable default settings that it refers to at initialization.  The default settings
(and factory settings) are listed in Table 1-8.

Setting Method

The method of setting defaults is shown in the flowchart below.

ATTENTION

❒

 Any default value specified is not stored in the EEPROM until the printer is turned off.

❒

 The last default value specified before power off is stored in the EEPROM.

E N D

Change the settings?

Y E S

N O

Change setting menu:  Alt button
Change setting value:  Pause button
 

Turn printer power off to  save settings to the EEPROM.on the main board

S TA RT

Hold down the Economy /Condensed 
button, and turn on the printer.

The printer prints:
1. Firmware version, 
    Protect counter value A/C.
2. How to set defaults.
3. Current settings.

Figure 1-6. Default Setting Flowchart

Printer Features

EPSON Stylus 1500 Service Manual

1-19

Summary of Contents for Stylus 1500


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands