Epson Stylus 1500 Service Manual Download Page 129

Page: 129 / 185

Refer to the pattern and input a value from –12 to 12 to align both black and magenta lines (or
to bring F within 0

0.035 mm), as shown in the following flowchart.

Press ENTER to exit the setting mode, or press SPACE to continue making settings.

CAUTION

❒

The values are not permanently stored in EEPROM until the printer is turned off. Turn
off the printer immediately after adjustment.

❒

Reset protect counter B using the adjustment program to make the printer perform the
initial ink charge operation before sending the unit back to the customer.

The menu below appears on the display. To end the program, press 5.

Stylus 1500 <********> Customer Data <********> 95/**/**

( Customer Data Input

) .... 1

( Adjustment

) .... 2

( END ) .... 5
SELECT MENU

■

10. Turn off the printer.

START

Choose " Head Gap Adj." to enter
the head gap adjustment

Select the resolution

Is the head gap OK ?

To main menu

Which direction is
the pattern ?

Input -1 value and
ENTER key

Input +1 value and
ENTER key

Press ENTER key

Are all resolutions
OK ?

YES

Press ENTER key

Figure 4-18. Head Gap Adjustment Flowchart

Adjustments

4-26

EPSON Stylus 1500 Service Manual

Summary of Contents for Stylus 1500


























































































































































































Search results

Summary of Contents for Stylus 1500

Reviews:

Brands by name

Popular brands

Epson Stylus 1500, Service Manual

Search results

Summary of Contents for Stylus 1500

Reviews:

Brands by name

Popular brands