manualshive.com logo in svg

Epson Stylus 1500, Service Manual

Share
Download
Epson Stylus 1500 Service Manual Download Page 125

 Black - Color Head Vertical Adjustment

This adjustment sets the vertical position for the black and color heads. (Aligning the top nozzle for
both, the # 4 nozzle on the black head and the # 1 nozzle on the color head, and aligning the bottom
nozzle for both, the # 61 nozzle on the black head and the # 20 nozzle of the color head.)  Make this
adjustment using this adjustment program and set the Adjustment mode to Pattern 7 on the control
panel. (See page 1-22.)  This adjustment is required when the black head or the color head is
replaced or disassembled. The following figure illustrates this adjustment.

CAUTION

When you replace the black head, always adjust its angle first, because the black - color
head vertical adjustment is based on the black head angle.

1.

Connect a PC to the printer via LPT1 using a parallel interface cable, and turn the printer on.

2.

Load GW-BASIC on the PC and run the program ST1500.BAS.  The main menu appears:

Customer Data
Printer Setting

[********]

3.

Using Table 4-3, input the 8-digit ID number for the destination as the printer setting for
“Customer Data.”  (For example, the U.S. market, or EAI:  20000A00). Then the menu below
appears:

Stylus 1500  
Customer Data <********> 95/**/**
<< Menu 1 >>                          

<<Menu 2>>

Head Data Writing                     

--------------

-----------------                              

--------------

Black Head Angle Adj.               

END

Uni-D Adj.                                  

Destination Data Writing only

Bi-D Adj.                                     

Initial Ink Charging

Color Head Angle Adj.              

Black - Color HV Adj.

                                                     Head Gap Adj.
                                                   

--------------

Select:<Up> or <Down> Go:<SPACE> or <ENTER> Change menu:<1> or <2>

4.

Move the cursor to “Black-Color HV Adj.” to perform the Black - Color Head vertical
adjustment operation by pressing 1, 2, 

↑

,  and  

↓

.

5.

Press SPACE and ENTER to enter the adjustment mode. The adjustment selection menu
appears, and the adjustment patterns are printed as follows:

# 1

# 1

# 1

# 1

# 2

# 2

# 2

# 2

# 3

# 4

# 1 9

# 1 9

# 1 9

# 2 0

# 2 0

# 2 0

# 6 1

# 6 2

# 6 3

# 6 4

Bla ck  He a d

C ol or   H e ad

M a g e n t a

C y a n

Y e llo w

Carriage Unit

Adjustment Directions

Paper Eject Direction

Figure 4-14. Black - Color Head Vertical Adjustment

Adjustments

4-22

EPSON Stylus 1500 Service Manual

Summary of Contents for Stylus 1500


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands